PT-600 Mechanized Plasma Cutting Torch
PT-600 Mechanized Plasma Cutting Torch
PT-600 Mechanized Plasma Cutting Torch
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
SECTION 4<br />
OPERATION<br />
Table 4-4. 200 Amp Data<br />
Nozzle - 200 Amp P/N 0558001884 Pilot Arc - HIGH<br />
Electrode - Hafnium P/N 0558001624<br />
Gas Baffle - 4 Hole P/N 0558002533 Not a drop cut<br />
Shield 100 - 250 Amp P/N 21802 Piercing thicker than 1" (25.4mm) is not recommended.<br />
Diffuser 100 - 360 Amp P/N 21944 If attempting set shield gas to 85 psi (5.86 bar) or higher<br />
Material<br />
Type-Thickness<br />
in.(mm)<br />
Current<br />
(Amps)<br />
Travel<br />
Speed<br />
ipm(m/min)<br />
Pierce<br />
Height<br />
in.(mm)<br />
<strong>Cutting</strong><br />
Height<br />
in.(mm)<br />
Arc<br />
Voltage<br />
(Volts)<br />
CS - 1/4 (6.4) 200 150 (3.8) 3/8 (9.6) 1/8 (3.2) 143 Air - 30 (2.07) Air - 45 (3.1) Air - 65 (4.48)<br />
CS - 3/8 (9.6) 100 (2.54) 146<br />
CS - 1/2 (12.7) 95 (2.4) 7/32 (5.5) 158<br />
CS - 5/8 (15.8) 75 (1.9) 1/2 (12.7) 160 Air - 55 (3.8)<br />
CS - 3/4 (19) 65 (1.65) 1/4 (6.4) 165<br />
CS - 1 (25.4) 35 (.89) 3/8 (9.6) 180 Air - 65 (4.48)<br />
CS - 1/4 (6.4) 200 170 (4.3) 3/8 99.6) 1/8 (3.2) 129 N 2<br />
- 30 (2.07) O 2<br />
- 45 (3.1) Air - 65 (4.48)<br />
CS - 3/8 (9.6) 110 (2.8) 3/16 (4.8) 133<br />
CS - 1/2 (12.7) 95 (2.4) 7/32 (5.5) 136<br />
CS - 5/8 (15.8) 75 (1.9) 1/2 (12.7) 139 Air - 55 (3.8)<br />
CS - 3/4 (19) 55 (1.4) 1/4 (6.4) 142<br />
CS - 1 (25.4) 40 (1.0) 3/8 (9.6) 155 Air - 65 (4.48)<br />
SS - 1/4 (6.4) 200 140 (3.6) 3/8 (9.6) 1/8 (3.2) 142 Air - 30 (2.07) Air - 52 (3.6) Air - 85 (5.86)<br />
SS - 3/8 (9.6) 125 (3.2) 3/16 (4.8) 150<br />
SS - 1/2 (12.7) 85 (2.2) 154<br />
SS - 3/4 (19) 55 (1.4) 1/2 (12.7) 3/8 (9.6) 174<br />
SS - 1 (25.4) 20 (.50) 180<br />
AL - 1/4 (6.4) 200 125 (3.2) 3/8 (9.6) 3/16 (4.8) 155 Air - 30 (2.07) Air - 52 (3.6) Air - 85 (5.86)<br />
AL - 3/8 (9.6) 110 (2.8) 1/4 (6.4) 165<br />
AL - 1/2 (12.7) 85 (2.2) 167<br />
Al - 3/4 (19) 60 (1.5) 1/2 (12.7) 3/8 (9.6) 182<br />
AL -1 (25.4) 40 (1.02) 189<br />
Start Gas<br />
Type/Pressure<br />
psi(bar)<br />
<strong>Plasma</strong> Gas<br />
Type/Pressure<br />
psi(bar)<br />
Shield Gas<br />
Type/Pressure<br />
psi(bar)<br />
NOTES:<br />
CS - Carbon Steel, SS - Stainless Steel, AL - Aluminum<br />
All N 2<br />
<strong>Plasma</strong>/Air Shield, 200 Amp cuts on Aluminum and Stainless Steel have fair surfaces except 1" (25.4mm) AL that is poor.<br />
4-insert
Change language