PT-600 Mechanized Plasma Cutting Torch

More documents

Recommendations

Info

PT-600 Plasma Cutting Torch Table of Contents This page intentionally left blank iv
SECTION 1 1.1 Introduction 1.2 Safety Notations And Symbols ! SAFETY The process of cutting metals with plasma equipment provides industry with a valuable and versatile tool. ESAB cutting machines are designed to provide both operation safety and efficiency. However, as with any machine tool, sensible attention to operating procedures, precautions, and safe practices is necessary to achieve a full measure of usefulness. Whether an individual is involved with operation, servicing, or as an observer, compliance with established precautions and safe practices must be accomplished. Failure to observe certain precautions could result in serious personnel injury or severe equipment damage. The following precautions are general guidelines applicable when working with cutting machines. More explicit precautions pertaining to the basic machine and accessories are found in the instruction literature. For a wide scope of safety information on the field of cutting and welding apparatus, obtain and read the publications listed in the Recommended References. The following words and symbols are used throughout this manual. They indicate different levels of required safety involvement. ALERT or ATTENTION. Your safety is involved or potential equipment failure exists. Used in concurrence with other symbols and information. ! ! ! DANGER WARNING CAUTION CAUTION NOTICE Used to call attention to immediate hazards which, if not avoided, will result in serious personal injury or loss of life. Used to call attention to potential hazards that could result in personal injury or loss of life. Used to call attention to hazards that could result in minor personal injury or equipment damage. Used to call attention to minor hazards to equipment. Used to call attention to important installation, operation or maintenance information not directly related to safety hazards. 1-1
Page 1 and 2: F-15-646 October, 2011 Installation
Page 3: Type of equipment Materialslag DECL
Page 6 and 7: PT-600 Plasma Cutting Torch Table o
Page 10 and 11: SECTION 1 SAFETY 1.3 General Safety
Page 12 and 13: SECTION 1 SAFETY 1.5 Operating A Pl
Page 14 and 15: SECTION 1 SAFETY ! WARNING Radiatio
Page 16 and 17: SECTION 1 ! DANGER Hydrogen explosi
Page 18 and 19: SECTION 1 1.7 Safety References SAF
Page 20 and 21: SECTION 2 DESCRIPTION 2.4 PT-600 Te
Page 22 and 23: SECTION 2 DESCRIPTION 2.5.2 Spare P
Page 24 and 25: SECTION 3 INSTALLATION Torch 5. Sli
Page 26 and 27: SECTION 3 INSTALLATION 3.4 Mounting
Page 28 and 29: SECTION 4 ! WARNING OPERATION Oil A
Page 30 and 31: SECTION 4 OPERATION Part Positive C
Page 32 and 33: SECTION 4 OPERATION 4.2.5 Dross Dro
Page 34 and 35: SECTION 4 OPERATION 4.3 Torch Flow
Page 36 and 37: SECTION 4 OPERATION 4.4.2 Aluminum
Page 38 and 39: SECTION 4 OPERATION 4.4.4 Stainless
Page 40 and 41: SECTION 4 OPERATION PT-600 Plasma A
Page 42 and 43: SECTION 4 PT-600 Plasma Arc Cutting
Page 50 and 51: SECTION 4 OPERATION Material: Carbo
Page 58 and 59:
SECTION 4 OPERATION PT-600 Plasma A
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
SECTION 4 PT-600 Plasma Arc Cutting
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
SECTION 4 OPERATION PT-600 Material
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
SECTION 4 OPERATION CUTTING PARAMET
Page 134 and 135:
SECTION 4 Table 4-3. 150 Amp Data O
Page 136 and 137:
SECTION 4 OPERATION Table 4-4. 200
Page 138 and 139:
SECTION 4 OPERATION CUTTING PARAMET
Page 140 and 141:
SECTION 4 OPERATION LOW CURRENT CUT
Page 142 and 143:
SECTION 4 OPERATION 3-8. HIGH CURRE
Page 144 and 145:
SECTION 4 OPERATION PT-600 50-65 AM
Page 146 and 147:
SECTION 4 PT-600 100 AMP Cutting Da
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
SECTION 4 OPERATION PT-600 360 AMP
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
SECTION 5 Maintenance ! WARNING Hot
Page 160 and 161:
SECTION 5 Maintenance 6. Disassembl
Page 162 and 163:
SECTION 5 Maintenance This page int
Page 164 and 165:
SECTION 6 6.2 No Pilot Arc Smart Fl
Page 166 and 167:
SECTION 6 Troubleshooting This page
Page 168 and 169:
SECTION 7 REPLACEMENT PARTS 7.3 PT-
Page 170 and 171:
SECTION 7 REPLACEMENT PARTS 7.4 Hos
Page 172 and 173:
SECTION 7 REPLACEMENT PARTS 7.5 Com
Page 174 and 175:
SECTION 7 REPLACEMENT PARTS 7.6 Par
Page 176 and 177:
SECTION 7 REPLACEMENT PARTS 7.6 200
Page 178 and 179:
SECTION 7 REPLACEMENT PARTS Item No
Page 180 and 181:
SECTION 7 REPLACEMENT PARTS 10 REF
Page 182 and 183:
SECTION 7 REPLACEMENT PARTS PLASMA
Page 184 and 185:
SECTION 7 REPLACEMENT PARTS (8)0558
Page 186:
Customer // Technical Support (843)
show all

PT-600 Mechanized Plasma Cutting Torch

Create successful ePaper yourself

Delete template?

Save as template?