PT-600 Mechanized Plasma Cutting Torch

More documents

Recommendations

Info

SECTION 4 OPERATION Part Positive Cut Angle Top dimension is less than the bottom dimension. • Misaligned torch Drop Part • Bent or warped material • Worn or damaged consumables • High standoff high (arc voltage) • <strong>Cutting</strong> speed fast • Current high or low. (See process data for recommended current level for specific nozzles). • Wrong secondary gas flow. 4.2.3 Cut Flatness Top And Bottom Rounded Condition usually occurs when material is 0.25" thick (6,4mm) or less. • High current for given material thickness (See process data for proper settings). Drop Part 4-4
SECTION 4 OPERATION Top Edge Undercut Standoff low (arc voltage) Drop Part 4.2.4 Surface Finish Process Induced Roughness Cut face is consistently rough and may be confined to one axis. Top View • Incorrect shield gas mixture (See process data) • Worn or damaged consumables Cut Face Machine Induced Roughness Can be difficult to distinguish from process induced roughness and is often confined to one axis. Roughness is inconsistent. or Process Induced Roughness Machine Induced Roughness • Dirty rails, wheels and/or drive rack/pinion. (Refer to maintenance section in machine owner’s manual). • Carriage wheel adjustment 4-5
Page 1 and 2: F-15-646 October, 2011 Installation
Page 3: Type of equipment Materialslag DECL
Page 6 and 7: PT-600 Plasma Cutting Torch Table o
Page 8 and 9: PT-600 Plasma Cutting Torch Table o
Page 10 and 11: SECTION 1 SAFETY 1.3 General Safety
Page 12 and 13: SECTION 1 SAFETY 1.5 Operating A Pl
Page 14 and 15: SECTION 1 SAFETY ! WARNING Radiatio
Page 16 and 17: SECTION 1 ! DANGER Hydrogen explosi
Page 18 and 19: SECTION 1 1.7 Safety References SAF
Page 20 and 21: SECTION 2 DESCRIPTION 2.4 PT-600 Te
Page 22 and 23: SECTION 2 DESCRIPTION 2.5.2 Spare P
Page 24 and 25: SECTION 3 INSTALLATION Torch 5. Sli
Page 26 and 27: SECTION 3 INSTALLATION 3.4 Mounting
Page 28 and 29: SECTION 4 ! WARNING OPERATION Oil A
Page 32 and 33: SECTION 4 OPERATION 4.2.5 Dross Dro
Page 34 and 35: SECTION 4 OPERATION 4.3 Torch Flow
Page 36 and 37: SECTION 4 OPERATION 4.4.2 Aluminum
Page 38 and 39: SECTION 4 OPERATION 4.4.4 Stainless
Page 40 and 41: SECTION 4 OPERATION PT-600 Plasma A
Page 42 and 43: SECTION 4 PT-600 Plasma Arc Cutting
Page 50 and 51: SECTION 4 OPERATION Material: Carbo
Page 80 and 81:
SECTION 4 PT-600 Plasma Arc Cutting
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
SECTION 4 OPERATION PT-600 Material
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
SECTION 4 OPERATION CUTTING PARAMET
Page 134 and 135:
SECTION 4 Table 4-3. 150 Amp Data O
Page 136 and 137:
SECTION 4 OPERATION Table 4-4. 200
Page 138 and 139:
SECTION 4 OPERATION CUTTING PARAMET
Page 140 and 141:
SECTION 4 OPERATION LOW CURRENT CUT
Page 142 and 143:
SECTION 4 OPERATION 3-8. HIGH CURRE
Page 144 and 145:
SECTION 4 OPERATION PT-600 50-65 AM
Page 146 and 147:
SECTION 4 PT-600 100 AMP Cutting Da
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
SECTION 4 OPERATION PT-600 360 AMP
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
SECTION 5 Maintenance ! WARNING Hot
Page 160 and 161:
SECTION 5 Maintenance 6. Disassembl
Page 162 and 163:
SECTION 5 Maintenance This page int
Page 164 and 165:
SECTION 6 6.2 No Pilot Arc Smart Fl
Page 166 and 167:
SECTION 6 Troubleshooting This page
Page 168 and 169:
SECTION 7 REPLACEMENT PARTS 7.3 PT-
Page 170 and 171:
SECTION 7 REPLACEMENT PARTS 7.4 Hos
Page 172 and 173:
SECTION 7 REPLACEMENT PARTS 7.5 Com
Page 174 and 175:
SECTION 7 REPLACEMENT PARTS 7.6 Par
Page 176 and 177:
SECTION 7 REPLACEMENT PARTS 7.6 200
Page 178 and 179:
SECTION 7 REPLACEMENT PARTS Item No
Page 180 and 181:
SECTION 7 REPLACEMENT PARTS 10 REF
Page 182 and 183:
SECTION 7 REPLACEMENT PARTS PLASMA
Page 184 and 185:
SECTION 7 REPLACEMENT PARTS (8)0558
Page 186:
Customer // Technical Support (843)
show all

PT-600 Mechanized Plasma Cutting Torch

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?