Yotta RAID Software installation guide - Axus

More documents

Recommendations

Info

Software Operation ManualFiber ParamsThe parameters of the fiber channel connection(s) to the host(s) are set and reconfigured fromthe FC (fiber channel) params submenu located at Main menu > FC params menu.YOTTA RAID is available in two hardware configurations: With a fiberchannel interface and with a SCSI interface. The FC Params menu is onlypresent on the fiber channel interface configuration. User of the SCSI interfacemodel should ignore this section.Fiber Params Menu Tree- 40 -
Software Operation ManualPrimary FiberSubmenu for configuring Primary Fiber settingsEnable Hard Loop IDEnable Hard Loop ID if you wish to enter the ID manually. Disable to have theID set by the controller (Default: Disable).Set Hard Loop IDEnter the Hard Loop ID for this controller (only applicable if 2.1.1 is set toEnable).Set Connection ModeArbitration Loop or Point-to-Point (Default: Arbitration Loop).Set Data Rate1 Giga-bits, 2 Giga-bits or Auto-negotiated (Default: Auto-negotiated).LUN MapSelect a Logical Unit Number (LUN 0 to LUN 7) or enter the desired LUN (LUN#, up to LUN 127) and a corresponding slice on which to map it.Secondary FCSubmenu for configuring Secondary Fiber Channel settings for use in multiplehost topology (submenu items 2.2.1 to 2.2.5 as above)Configuration changes made in the FC Params menu must be saved to theYOTTA RAID non-volatile memory and YOTTA RAID restarted for thechanges to take effect. This is done in the NVRAM menu accessed from theMain menu. See Saving Configurations later in this chapter.SAN MaskSAN Mask (LUN Masking) is a differentiation tool for use on fiber networksbased on the unique Worldwide Name (WWN) of each fiber card. SAN Maskingallows an administrator to specify which hosts are able to see the RAIDcontroller.Visible For All HostsUse this submenu to select whether the RAID controller is visible to connectedhosts.SupportingChannel 1 or Channel 2. To Enable/Disable San Mask support.SAN MappingSAN Mapping allows the administrator to map individual LUNs to a specifiedhost thereby limiting access to certain slices to single hosts even in a dual hostconfiguration.Select PortPort 1 or Port 2. The two ports are equivalent to the two host channels.- 41 -
Page 5 and 6: Software Operation ManualTable of C
Page 7 and 8: Software Operation ManualSCSI Param
Page 9 and 10: Software Operation ManualConfigurat
Page 11: Software Operation ManualChapter 1I
Page 15 and 16: Software Operation ManualArray Mana
Page 17 and 18: Software Operation ManualQuick Setu
Page 19 and 20: Software Operation ManualChapter 3A
Page 21 and 22: Software Operation ManualUsing the
Page 23 and 24: Software Operation ManualMonitor ut
Page 25 and 26: Software Operation ManualUpdatepass
Page 27 and 28: Software Operation ManualHow to con
Page 29 and 30: Software Operation ManualAccessing
Page 31 and 32: Software Operation ManualAccessing
Page 33 and 34: Software Operation ManualArray Para
Page 35 and 36: Software Operation ManualSlice 0~Sl
Page 37 and 38: Software Operation ManualSCSI Param
Page 39: Software Operation ManualQASEnable
Page 43 and 44: Software Operation ManualSetting Sy
Page 45 and 46: Software Operation ManualTerminal P
Page 47 and 48: Software Operation ManualPager aler
Page 49 and 50: Software Operation ManualModem sett
Page 51 and 52: Software Operation ManualUtilityUti
Page 53 and 54: Software Operation ManualOverwrite
Page 55 and 56: Software Operation ManualStart Perm
Page 57 and 58: Software Operation ManualSave Confi
Page 59 and 60: Software Operation ManualChapter 5R
Page 61 and 62: Software Operation ManualSystem Inf
Page 63 and 64: Software Operation ManualSystem is
Page 65 and 66: Software Operation ManualThe role i
Page 67 and 68: Software Operation ManualMain Confi
Page 69 and 70: Software Operation ManualIf there i
Page 71 and 72: Software Operation ManualExpand Arr
Page 73 and 74: Software Operation ManualDisk self
Page 75 and 76: Software Operation ManualConfigurat
Page 77 and 78: Software Operation ManualComm param
Page 79 and 80: Software Operation ManualNotify Par
Page 81 and 82: Software Operation ManualAppendix A
Page 83 and 84: Software Operation ManualProblems d
Page 85 and 86: Software Operation ManualFix: Chang
Page 87 and 88: Software Operation ManualRAID 0RAID
Page 89 and 90: Software Operation ManualRAID 0+1RA
Page 91 and 92:
Software Operation ManualRAID 30RAI
Page 93 and 94:
Software Operation ManualRAID 50RAI
Page 95 and 96:
Software Operation ManualTriple Par
Page 97 and 98:
Software Operation ManualNRAIDNRAID
Page 99 and 100:
Software Operation ManualAppendix D
Page 101 and 102:
Software Operation ManualHot SwapTh
Page 103 and 104:
Software Operation ManualAs usual i
Page 105 and 106:
Software Operation ManualLUN map: Y
Page 107 and 108:
Software Operation ManualAppendix H
Page 109 and 110:
Software Operation ManualAppendix I
show all

Yotta RAID Software installation guide - Axus

Create successful ePaper yourself

Delete template?

Save as template?