AT Commands Manual - Teltonika

More documents

Recommendations

Info

AT CommandsUser Manual-"HEX" character strings consist only of hexadecimal numbers from 00 to FF; e.g. "032FE6" equals three8-bit characters with decimal values 3, 47 and 230; no conversions to the original MT character set shall bedone.- “IRA”: international reference alphabet (ITU-T T.50).- “PCCP437”: PC character set Code Page 437.- “8859-1”: ISO 8859 Latin 1 character set.- “UCS2”: 16-bit universal multiple-octet coded character set (USO/IEC10646); UCS2 character stringsare converted to hexadecimal numbers from 0000 to FFFF. Only the strings found in quotation marks areUCS2 coded, the rest of commands or responses remain inIRA alphabet.4.6 Request international mobile subscriber identification +CIMICommand syntaxDescriptionThis command allows requesting the international mobile subscriber identity IMSI(International Mobile Subscriber Identity), which is intended to permit the TE user to identifythe individual SIM which is attached to ME. AT+CIMI 1 OKorCME ERROR: Test commandOKAT+CIMI=?4.7 Card identification +CCIDCommand syntaxDescriptionThis command returns the ICCID of the SIM-card. AT+CCID OKorCME ERROR: Read commandsame as aboveAT+CCID?Test commandOKAT+CCID=?4.8 Request complete capabilities list +GCAPCommand syntaxDescriptionThis command requests the list of capabilities, containing the corresponding command names.+GCAP: +FCLASS, +CGSMAT+GCAP 2 OKorCME ERROR: unknown4.9 Repeat last command A/Command syntaxDescriptionA/ This syntax allows repeating the previously executed command again. Only the A/ commandcan not be repeated.1 Read the IMSI (15 digits starting with MCC / 3 digits and MNC / 2digits).2 Get the list of capabilities.10
AT CommandsUser Manual5 Mobile equipment control and status commands5.1 Phone activity status +CPASCommand syntaxAT+CPASTest commandAT+CPAS=?DescriptionThis execution command returns the activity status of the MT. +CPAS: OKorCME ERROR: OK may be:- 0: ready (MT allows commands from TA/TE)- 1: unavailable (MT does not allow commands from TA/TE)- 2: unknown (MT is not guaranteed to respond to instructions)- 3: ringing (MT is ready for commands from TA/TE, but the ringer is active)- 4: call in progress (MT is ready for commands from TA/TE, but a call is in progress)- 5: asleep (MT is unable to process commands from TA/TE because it is in a low functionality state)5.2 Switch off MS +CPWROFFCommand syntaxAT+CPWROFFTest commandAT+CPWROFF=?DescriptionThis command allows to switch off the MS.Note: Usage of this command implies that the part of command line placed thereafter will beignoredOKorCME ERROR: OK5.3 Set phone functionality +CFUNCommand syntaxDescriptionAT+CFUN= This command selects the level of functionality in the MS. Only some values of are allowed (see Defined values).Note: if the syntaxes +CFUN=0 or +CFUN=15 (resets) are used, the rest of the commandline, placed after that, will be ignored.AT+CFUN=0 OKorCME ERROR: AT+CFUN=1 Set full functionality modeOKAT+CFUN=6 Allow SIM-TK commands and enables fetching of proactive commands by SIM-PPL fromSIMOKAT-CFUN=7 Disable SIM-TK commands and enables fetching of proactive commands by SIM-PPL fromSIMOKAT-CFUN=8 Disable fetching of proactive commands by SIM-APPL from SIM-cardOKAT-CFUN=15 Reset MS without resetting SIMRead command+CFUN:AT+CFUN?,Test command+CFUN: (list of supported ’s) e.g. +CFUN: (0,1,6,7,8,15)AT+CFUN=?OK selected functionality which may be:- 0 : minimum functionality meaning switch off of the MS- 1: full functionality meaning start up MS (from offline mode)11
Page 7 and 8: AT CommandsUser Manual1 Introductio
Page 9: AT CommandsUser Manual4 General com
Page 13 and 14: AT CommandsUser Manual5.6 Display c
Page 15 and 16: AT CommandsUser Manual− 1: indica
Page 17 and 18: AT CommandsUser Manual may be− 17
Page 19 and 20: AT CommandsUser Manual5.17 Call met
Page 21 and 22: AT CommandsUser Manual6 Call Contro
Page 23 and 24: AT CommandsUser ManualCommand synta
Page 25 and 26: AT CommandsUser Manual7 Network Ser
Page 27 and 28: AT CommandsUser Manual7.4 Network r
Page 29 and 30: AT CommandsUser Manual8 Security Co
Page 31 and 32: AT CommandsUser Manual9 Phonebook C
Page 33 and 34: AT CommandsUser Manual10 Short Mess
Page 35 and 36: AT CommandsUser Manual may be:− 0
Page 37 and 38: AT CommandsUser Manual10.9 Read mes
Page 39 and 40: AT CommandsUser Manual10.13 Write m
Page 41 and 42: AT CommandsUser Manual11 Supplement
Page 43 and 44: AT CommandsUser Manual string type
Page 45 and 46: AT CommandsUser Manual11.6 Advise o
Page 47 and 48: AT CommandsUser ManualAT+CTFR=? is
Page 49: AT CommandsUser ManualTest commandA
Page 52: AT CommandsUser Manualservice will
Page 57 and 58: AT CommandsUser Manual13.17 Call te
Page 59 and 60: AT CommandsUser Manual may be in ra
Page 61 and 62:
AT CommandsUser Manual14 V24 contro
Page 63 and 64:
AT CommandsUser ManualCME ERROR: 14
Page 65 and 66:
AT CommandsUser Manual may be:− 0
Page 67 and 68:
AT CommandsUser Manual is in range
Page 69 and 70:
AT CommandsUser Manual15 Specific A
Page 71 and 72:
AT CommandsUser Manual: Channel mod
Page 73 and 74:
AT CommandsUser Manual- 2: dialing
Page 75 and 76:
AT CommandsUser Manual15.11 Configu
Page 77 and 78:
AT CommandsUser ManualSIM ToolkitTh
Page 79 and 80:
AT CommandsUser Manual may be (deci
Page 83 and 84:
AT CommandsUser Manual- 0 detached.
Page 85 and 86:
AT CommandsUser ManualAT+CGATT?Test
Page 87 and 88:
AT CommandsUser Manual16.11 GPRS mo
Page 89 and 90:
AT CommandsUser Manual17 Appendices
Page 91 and 92:
AT CommandsUser Manual16 normal cal
show all

AT Commands Manual - Teltonika

Create successful ePaper yourself

Delete template?

Save as template?