AT Commands Manual - Teltonika

More documents

Recommendations

Info

AT CommandsUser Manual integer type value indicating:− 0: disable time zone change event reporting (default)− 1: enable time zone change event reporting.: integer value indicating the time zone.5.21 Report mobile termination error +CMEECommand syntaxDescriptionAT+CMEE=[]This set command enables or disables the use of result code +CME ERROR: asan indication of an error relating to the functionality of the MT. When enabled, MTrelated errors cause +CME ERROR: final result code instead of the regularERROR final result code. ERROR is returned normally when error is related to syntax,invalid parameters or TA functionality.Read command+CMEE: AT+CMEE?OKTest command+CMEE: (0-2) i.e. list of supp.sAT+CMEE=?OK may be:− 0 disable +CME ERROR: result code and use ERROR instead.− 1 enable +CME ERROR: result code and use numeric values.− 2 enable +CME ERROR: result code and use verbose values.Note: in case of selected value +CMEE=2, meaning formatting the error result code as +CME ERROR: with as verbosevalue, the following convention is valid: if the error result code is related to a parameter not covered by the GSM/ETSI or Teltonika specificationthe value ="operation not supported" shall be used if the TA is in a state which not allow to perform the entered command, the value="operation not allowed" shall be used.5.22 List all available AT commands +CLACCommand syntaxDescriptionAT+CLACThis execution command causes the MS to return one or more lines of AT commandsthat are available for the DTE user. Each line contains one AT command. Thepresentation of commands respects the order in the AT-manual.Test commandOKAT+CLAC=? defines the AT command including the prefix AT. The text does not contain the sequence0 or OK.20
AT CommandsUser Manual6 Call Control CommandsNote: Because the type of address is automatically detected on the dial string of the D command, the +CSTA command has really no effect.6.1 Select type of address +CSTACommand syntaxDescriptionAT+CSTA=[]This set command selects the type of number for further dialing commands (D)according to GSM specifications.Read command+CSTA: AT+CSTA?OKTest command+CSTA: (129,145)AT+CSTA=?OK may be:− 145 when dialing string includes international access code character “+”.− 129 when the dial string begins with a digit.6.2 Dial command D6.2.1 DescriptionThe V.24ter dial command D lists characters that may be used in a dialing string for making a call or controllingsupplementary services in accordance with GSM02.30 and initiates the indicated kind of call. No furthercommands may follow in the command line. The command is abortable by hit a key before establishment.6.2.2 V.25ter dialing digitsThey are: 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, *,#, +, A, B, C. Character D is allowed but ignored.6.2.3 V.25ter or GSM modifier characters− “,”, “T”, “P”, “!”, “W” or “@” are ignored.− “;” forces a voice call originated to the given address.− “>” allows direct dialling from phonebook.− “I” invocation restrict CLI presentation.− “i” suppression i.e. allows CLI presentation.− “G” or “g” control the CUG supplementary service information for this call (s.+CCUG).6.2.4 Direct calling from phonebooksD>[I][G][;] originate a call to phone number which corresponding alphanumeric field in the defaultphonebook is .D>mem[I][G][;] originate a call to phone number in memory (one of the phonebooks) “mem” entrylocation . ”mem” may be for example “SM”, “FD” or “LD”.D>[I][G][;] originate a call to phone number in entry location of the default phonebook. Thesemicolon character shall be added when a voice call is originated. CLIR and CUG per call modifiers can also bepresent.21
Page 7 and 8: AT CommandsUser Manual1 Introductio
Page 9 and 10: AT CommandsUser Manual4 General com
Page 11 and 12: AT CommandsUser Manual5 Mobile equi
Page 13 and 14: AT CommandsUser Manual5.6 Display c
Page 15 and 16: AT CommandsUser Manual− 1: indica
Page 17 and 18: AT CommandsUser Manual may be− 17
Page 19: AT CommandsUser Manual5.17 Call met
Page 23 and 24: AT CommandsUser ManualCommand synta
Page 25 and 26: AT CommandsUser Manual7 Network Ser
Page 27 and 28: AT CommandsUser Manual7.4 Network r
Page 29 and 30: AT CommandsUser Manual8 Security Co
Page 31 and 32: AT CommandsUser Manual9 Phonebook C
Page 33 and 34: AT CommandsUser Manual10 Short Mess
Page 35 and 36: AT CommandsUser Manual may be:− 0
Page 37 and 38: AT CommandsUser Manual10.9 Read mes
Page 39 and 40: AT CommandsUser Manual10.13 Write m
Page 41 and 42: AT CommandsUser Manual11 Supplement
Page 43 and 44: AT CommandsUser Manual string type
Page 45 and 46: AT CommandsUser Manual11.6 Advise o
Page 47 and 48: AT CommandsUser ManualAT+CTFR=? is
Page 49: AT CommandsUser ManualTest commandA
Page 52: AT CommandsUser Manualservice will
Page 57 and 58: AT CommandsUser Manual13.17 Call te
Page 59 and 60: AT CommandsUser Manual may be in ra
Page 61 and 62: AT CommandsUser Manual14 V24 contro
Page 63 and 64: AT CommandsUser ManualCME ERROR: 14
Page 65 and 66: AT CommandsUser Manual may be:− 0
Page 67 and 68: AT CommandsUser Manual is in range
Page 69 and 70: AT CommandsUser Manual15 Specific A
Page 71 and 72:
AT CommandsUser Manual: Channel mod
Page 73 and 74:
AT CommandsUser Manual- 2: dialing
Page 75 and 76:
AT CommandsUser Manual15.11 Configu
Page 77 and 78:
AT CommandsUser ManualSIM ToolkitTh
Page 79 and 80:
AT CommandsUser Manual may be (deci
Page 83 and 84:
AT CommandsUser Manual- 0 detached.
Page 85 and 86:
AT CommandsUser ManualAT+CGATT?Test
Page 87 and 88:
AT CommandsUser Manual16.11 GPRS mo
Page 89 and 90:
AT CommandsUser Manual17 Appendices
Page 91 and 92:
AT CommandsUser Manual16 normal cal
show all

AT Commands Manual - Teltonika

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?