<strong>AT</strong> <strong>Commands</strong>User <strong>Manual</strong>− 1: if SMS-DELIVER is stored in ME/TA, indication of the memory location is routed to the TE usingunsolicited result code: +CMTI: , .− 2: SMS-DELIVER (except class2 SMS) is routed directly to the TE using the unsolicited result code:+CMT: [ if PDU mode enabled or +CDS:,,[],[],>scts>,, if text mode enabled.− 2: if SMS-ST<strong>AT</strong>US-REPORT is stored into ME/TA, indication of the memory location is routed to theDTE using the unsolicited result code +CDSI: , may be:− 0: TA buffer of unsolicited result codes defined within this command is flushed to the TE when 1...3 is entered (OK response shall be given before flushing the codes).− 1: TA buffer of unsolicited result codes defined within this command is cleared when 1...3 isentered.Note: The parameters , , , , , , shall be displayed onlywhen setting +CSHD=1 is.Note: The syntax <strong>AT</strong>+CMGR=0 allows to display a SMS class 0 if it is signalized to TA, because noclassic MMI is available in the MS (s. also the note from command +CNMI).36
<strong>AT</strong> <strong>Commands</strong>User <strong>Manual</strong>10.9 Read message +CMGRCommand syntaxDescription+CMGR= This execution command returns message with location value from message storage to the TE.for SMS-DELIVER in text mode:+CMGR:,,[],[,,,,,,,] for SMS-SUBMIT in text mode:+CMGR:,,[][,,,,[],,,]for SMS-ST<strong>AT</strong>US-REPORT in text mode:+CMGR: ,,,[],[], for SMS-COMMAND in textmode:+CMGR:,,[,,[],[],[],]for CBM storage in text mode:+CMGR:,,,,, in PDU mode:+CMGR: ,[],<strong>AT</strong>+CMGR=3Test command<strong>AT</strong>+CMGR=?OKorCMS ERROR: OK: may be in range 0-400; value 0 is possible only if a SMS class 0 is received and previously the setting+CNMI=1,… was set may be:− 0 in PDU mode or “REC UNREAD” in text mode: received unread SMS− 1 in PDU mode or “REC READ” in text mode: received read SMS− 2 in PDU mode or “STO UNSENT” in text mode: stored unsent SMS− 3 in PDU mode or “”STO SENT” in text mode: stored sent SMS− 4 in PDU mode or “ALL” in text mode: all SMS’s10.10 New Message Acknowledgement to ME/TA +CNMACommand syntaxDescriptionif text modeThis execution command confirms correct reception of a new message (SMS-DELIVER(+CMGF=1 enabled) +CNMA or SMS-REPORT) which is routed directly to the TE. This acknowledgement commandif PDU mode(causing ME to send RP-ACK to the network) shall be used when +CSMS parameter(+CMGF=0 equals 1. MS shall not send another +CMT or +CDS result code to TE beforeenabled)+CNMA=previous one is acknowledged. If the mobile does not get the acknowledgement within,PDU< required time (network timeout), it must send RP-ERROR to the network. Both settingsctrl-Z/ESC> and of +CNMI command will be automatically set to zero. If the command+CNMA is received, but no acknowledgement is expected, or some other ME relatederrors occurs, a corresponding +CMS ERROR: is returned.<strong>AT</strong>+CNM<strong>AT</strong>est command<strong>AT</strong>+CNMA=?OKorCMS ERROR: