AT Commands Manual - Teltonika

More documents

Recommendations

Info

AT CommandsUser Manual15.8 Set/reset counter of sent or received GPRS data +XGCNTSETCommand syntaxDescriptionAT+XGCNTSET=, The command AT+XGCNTSET allows to set the counter for total sent/received bytes, for each defined context to zero or any other offset value. Whenever the total counter for a is set (to zero or a certain value), the sessioncounter for this will be set to zero.If the equals zero than the total counter for every defined context is set to zero.Given offset parameters are ignored in this case.AT+XGCNTSET=1,20,20Test commandAT+XGCNTSET=?OKorCME ERROR: +XGCNTSET: (0-255),(0-2147483646),(0-2147483646) i.e. (range of s), (range of), (range of )OK: integer containing the local PDP context identifier in range of 0-255.: long integer containing the offset of total sent bytes used for counting in range0-2147483646.: long integer containing the offset of total received bytes used for counting inrange 0-2147483646.15.9 Set hands free mode +XHANDSFREECommand syntaxDescriptionAT+XHANDSFREE= This command allows to set and get the hands free mode, i.e. switch from loudspeaker toearphone.AT+HANDSFREE=1Read commandAT+XHANDSFREE?Test commandAT+XHANDSFREE=?OKorCME ERROR: +XHANDSFREE: OK+XHANDSFREE: (0-1) i.e. (list of supported s)OKIn case of the read syntax, the response indicates also whether the user has switched from “not hands freemode” to a “hands free mode” using another AT command. may be:− 0: hands free not active.− 1: hands free active.15.10 Call the L1-specific function +XL1SETCommand syntaxDescriptionThis command allows to call L1-specific test and configuration functions. This command isAT+XL1SET=for internal test purpose only.AT+XL1SET=”xxx” OKorCME ERROR: values are specified from L1 Group and available via Intranet.74
AT CommandsUser Manual15.11 Configuration trace and modem (AT) interfaces +XSIOCommand syntaxDescriptionThis command allows the configuration of the modem-interface (AT), trace-interface, IrDAinterface,and MUXinterface by setting the variant number. The set variant number becomesactive only after a reset. The read command allows to see which is the current variant andAT+XSIO= which is the requested variant; a star marks the active variant. An overview about thepossible variants is delivered by the test syntax and customizable.AT+XSIO=1Read commandAT+XSIO?Test commandAT+XSIO=?Note: After variant change via this command, the user has to wait some seconds since the NVRAM is onlyupdated in the power saving period. Then reset the phone and the new device/protocol settings are active.OKorCME ERROR: +XSIO: ,*OK+XSIO: Variant=: AT=; Trace=;MUX=; IrDA= +XSIO:Variant=: AT=; Trace=; MUX=;IrDA=.................. (more display rows are possible)OK requested variant, which may be in range 0-255. currently active variant, which may be in range 0-255.: NULL, UART0, …, UARTn.: NULL, UART0, …, UARTn.: 1-x.: NULL, UART0, …, UARTn.15.12 ADC read command + NADCCommand syntaxDescriptionAT+NADC=This command reads the current value of the specified ADC, given in milliVolts.The syntax and the parameters range is shown in the response to the test command.Set commandAT+NADC=0Test commandAT+NADC=?+NADC:,OKorCME ERROR: +NADC: (0-adc_max_num)OK = ADC identifier, whose range (0-adc_max_num) depends on the specific platform (normally 2) = Current ADC value (0-2000 for ADC1, 0-2500 for ADC2 due to different ranges)15.13 GPIO select configuration command +NGPIOCCommand syntaxDescriptionAT+NGPIOC=,[,]Set commandAT+NGPIOC=3,0,1Test commandAT+NGPIOC=?This command allows the user to select the configuration of the availableGPIOs, which can be set in either input or output mode. The user may alsoselect the default value when the GPIO is configured in output. The syntaxand the parameters range is shown in the response to the test command.OKorCME ERROR: +NGPIOC: (0-gpio_max_num),(0-1)[,(0-1)]OK = GPIO identifier, whose range (0-gpio_max_num) depends on the specific platform (normally either 6 or 12) = GPIO mode, 0=output, 1=input = GPIO default value (0-1) for output configuration only75
Page 7 and 8:
AT CommandsUser Manual1 Introductio
Page 9 and 10:
AT CommandsUser Manual4 General com
Page 11 and 12:
AT CommandsUser Manual5 Mobile equi
Page 13 and 14:
AT CommandsUser Manual5.6 Display c
Page 15 and 16:
AT CommandsUser Manual− 1: indica
Page 17 and 18:
AT CommandsUser Manual may be− 17
Page 19 and 20:
AT CommandsUser Manual5.17 Call met
Page 21 and 22:
AT CommandsUser Manual6 Call Contro
Page 23 and 24: AT CommandsUser ManualCommand synta
Page 25 and 26: AT CommandsUser Manual7 Network Ser
Page 27 and 28: AT CommandsUser Manual7.4 Network r
Page 29 and 30: AT CommandsUser Manual8 Security Co
Page 31 and 32: AT CommandsUser Manual9 Phonebook C
Page 33 and 34: AT CommandsUser Manual10 Short Mess
Page 35 and 36: AT CommandsUser Manual may be:− 0
Page 37 and 38: AT CommandsUser Manual10.9 Read mes
Page 39 and 40: AT CommandsUser Manual10.13 Write m
Page 41 and 42: AT CommandsUser Manual11 Supplement
Page 43 and 44: AT CommandsUser Manual string type
Page 45 and 46: AT CommandsUser Manual11.6 Advise o
Page 47 and 48: AT CommandsUser ManualAT+CTFR=? is
Page 49: AT CommandsUser ManualTest commandA
Page 52: AT CommandsUser Manualservice will
Page 57 and 58: AT CommandsUser Manual13.17 Call te
Page 59 and 60: AT CommandsUser Manual may be in ra
Page 61 and 62: AT CommandsUser Manual14 V24 contro
Page 63 and 64: AT CommandsUser ManualCME ERROR: 14
Page 65 and 66: AT CommandsUser Manual may be:− 0
Page 67 and 68: AT CommandsUser Manual is in range
Page 69 and 70: AT CommandsUser Manual15 Specific A
Page 71 and 72: AT CommandsUser Manual: Channel mod
Page 73: AT CommandsUser Manual- 2: dialing
Page 77 and 78: AT CommandsUser ManualSIM ToolkitTh
Page 79 and 80: AT CommandsUser Manual may be (deci
Page 83 and 84: AT CommandsUser Manual- 0 detached.
Page 85 and 86: AT CommandsUser ManualAT+CGATT?Test
Page 87 and 88: AT CommandsUser Manual16.11 GPRS mo
Page 89 and 90: AT CommandsUser Manual17 Appendices
Page 91 and 92: AT CommandsUser Manual16 normal cal
show all

AT Commands Manual - Teltonika

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?