INDUSTRIAL DUTYSERIES HC26Dynapar brandIntegral Coupling <strong>Encoder</strong>Key Features• High 5000PPR Resolution Available• Integral Coupling and Flange ProvideThermal and Electrical Isolation• Field Replaceable CouplingSPECIFICATIONSSTANDARD OPERATING CHARACTERISTICSCode: IncrementalResolution: 3000 to 5000 PPR (pulses/revolution)Accuracy: (worst case any edge to any otheredge) ±10.8°/PPRFormat: Two channel quadrature (AB) withoptional Index (Z) and complementary outputsPhase Sense: A leads B for CW or CCW shaftrotation as viewed from the shaft end of theencoder; see Ordering InformationQuadrature Phasing: 90° ± 25° electricalSymmetry: 180° ± 25° electricalIndex: 90° ± 25° electrical (gated with B low)Waveforms: Squarewave with rise and fall timesless than 1 microsecond into a load capacitanceof 1000 pfELECTRICALInput Power:4.5 min. to 26 VDC max. at 80 mA max., notincluding output loadsOutputs:7273 Open Collector: 30 VDC max., 40 mA sinkmax.7272 Push-Pull and Differential Line Driver: 40 mAsink or sourceFrequency Response: 250 kHz min.Electrical Protection: Overvoltage, reverse voltageand output short circuit protectedNoise Immunity: Tested to EN61326 (Industrial)for Electro Static Discharge, Radio FrequencyInterference, Electrical Fast Transients, Conductedand Magnetic InterferenceMating Connector:7 pin, style MS3106A-16S-1S (MCN-N5);10 pin, style MS3106A-18-1S (MCN-N6)5 pin, style M12: Cable with connector available8 pin, style M12: Cable with connector availableMECHANICALShafts coupling: accepts 1/4", 3/8" and 1/2"motor or machinery shaftsShafts alignment: 0.002" max. TIR runout;0.005" max. radial offset; 3° max. angularShaft Speed: 10,000 RPM max.Starting Torque: (max at 25 °C) 1.0 oz-inMoment of Inertia: 4.3 x 10 -4 oz–in–sec 2ENVIRONMENTALOperating Temperature:Standard: 0 to +70 °C;Extended: –40 to +85 °CStorage Temperature: –40 to +90 °CShock: 50 G’s for 11 milliseconds durationVibration: 5 to 2000 Hz at 20 G’sHumidity: to 98% without condensationEnclosure Rating: NEMA12/IP54 (dirt tight,splashproof)2.58
yINDUSTRIAL DUTYSERIES HC26Ordering InformationTo order, complete the model number with code numbers from the table below:Code 1: ModelHC526Code 2: PPRCode 3: MechanicalCode 4: OutputCode 5: ElectricalCode 6: TerminationCode 7: OptionsOrdering InformationHC526Size 25 Enclosedwith IntegralCouplingand FlangeAdapter30003600409650003,0003,6004,0965,000A Flange Adapterwith PilotB Flange Adapterwithout PilotC Flange Adapterfor NEMA Size42 Motors7 Pin Connector or Cable0 Single Ended, no Index, Format A, Table 11 Single Ended, with Index, Format A, Table 14 Single Ended, with Index, Format B, Table 1A Single Ended, with Index, Format C, Table 1C Single Ended, no Index, Format C, Table 1G Single Ended, with Index, Format D, Table 110 Pin Connector or Cable2 Differential, no Index, Format A, Table 23 Differential, with Index, Format A, Table 25 Differential, with Index, Format B, Table 2B Differential, with Index Format C, Table 2D Differential, no Index, Format C, Table 25 Pin M12 ConnectorH Single ended, no index, Format A, Table 40 5-26V in; 5-26VOpen Collectorwith 2.2kΩPullup out1 5-26V in;5-26V OpenCollector out2 5-26V in; 5VTotem Poleout3 5-26V in; 5VDifferentialLine Driver out(7272)4 5-26V in;5-26VDifferentialLine Driver out(7272)0 End MountConnector1 Side MountConnector2 18" Cable, Side3 3' Cable, Side4 6' Cable, Side5 10' Cable, Side6 15' Cable, Sideavailable whenCode 4 is 0 thruG, and Code 6 is0 or 1:PS LED OutputIndicatorJ Single ended, with index, Format A, Table 4K Single ended, with index, Format B, Table 4L Single ended, with index, Format C, Table 4M Single ended, no index, Format C, Table 4N Single ended, with index, Format D, Table 48 Pin M12 ConnectorP Single ended, no index, Format A, Table 5Q Single ended, with index, Format A, Table 5R Single ended, with index, Format B, Table 5S Single ended, with index, Format C, Table 5T Single ended, no index, Format C, Table 5U Single ended, with index, Format D, Table 5V Differential, no index, Format A, Table 6W Differential, with index, Format A, Table 6A Same as "0"with extend.temp rangeB Same as "1"with extend.temp rangeC Same as "2"with extend.temp rangeD Same as "3"with extend.temp rangeE Same as "4"with extend.temp rangeX Differential, with index, Format B, Table 6Y Differential, with index, Format C, Table 6Z Differential, no index, Format C, Table 6CPLX1250375 Flexible Coupling 3/8" to 1/4", 3/8" or 1/2"10 foot Cable Assemblies with MS Connector1400431-0010 7 Pin MS, Cable Assy. For Use with Single Ended w/Index Outputs1400635-0010 10 Pin MS, Cable Assy. For Use with Differential Line Driver with Index Outputs15 foot Cable Assemblies with M12 Connector112859-0015 5 Pin M12, Cable Assy. For Use with Single Ended Outputs112860-0015 8 Pin M12, Cable Assy. For Use with Single Ended Outputs112860-0015 8 Pin M12, Cable Assy. For Use with Differential Line Driver OutputsMating Connectors (no cable)7 pin, style MS3106A-16S-1S (MCN-N5)10 pin, style MS3106A-18-1S (MCN-N6)2.59