Heavy Duty Encoder - Hengstler Encoders

yINDUSTRIAL DUTYSERIES AI25Ordering InformationTo order, complete the model number with code numbers from the table below:Code 1: Model Code 2: Bits Code 3 :Mounting Code 4: Shaft Size Code 5: Protocol Code 6: Electrical Code 7: ConnectorAI25AI25Size25AcuroAbsoluteEncoderDIMENSIONSØ42 ±0.1mm1.650.004inSingle-Turn0010 10 Bit0012 12 Bit0013 13 Bit0014 14 Bit0360 360 PPR(Gray excess)0720 720 PPR(Gray excess)Available when Code 6is 2Multi-Turn1212 12 Bit Multi-Turn, 12 BitSingle-Turn120°58mm2.28in10mm0.39inAvailable whenCode 4 is 0 or A0 Servo*Available whenCode 4 is 2 or C1 Clamping*Available whenCode 4 is 1 or B2 Squareflange**Available whenCode 4 is 3, 4,5 or 63 Hubshaftw/tether†* 58mm Dia.** 2.5" Square† 63mm BCCode 3: MountingMountingSurfacew/o shaft seal (IP64)0 6 mm1 3/8"2 10 mm3 3/8" Hub Shaft4 12 mm Hubshaft5 1/2" Hubshaft6 10 mm Hub Shaftw/ shaft seal (IP67)A 6 mmB 3/8"C 10 mmØ48±0.1mmØ1.89 ±0.004in45°20°0 ParallelBinary1 ParallelGray120 °120 °10mmDiameter0 5 VDC2 10-30 VDC10mm0.39in19.27mm0.76in9mm0.35in0 1.5m axial cable1 1.5m radial cableAvailable when Code 2 is00XX, 0360 or 07206 M23 Conin17 pin axial CW7 M23 Conin17 pin radial CW8 17 pin Conin axialCCW9 17 pin Conin radialJ 17 pin MS axial *K 19 pin Bayonet radialAvailable when Code 2is 1212A Cable 1.5m radial w/37 pin sub-DB Cable 1.5m axialw/37 pin sub-D* Status LED and Preset Switchfeatures not available with "J"M4x50Servo6mm4mm0.16in3mm0.12in3mm0.12in1ClampingM4x5M3x53mm0.12in15mm0.59inØ36mmØ1.42inMountingSurfaceØ31.75mm1.25inMountingSurface63.5mm2.5in52.4mm2.06in19.5mm ±0.30.77in ±0.013/8in Dia. Shaft7.5mm0.30in2Square Flange7mm0.28in63.5mm2.5in52.4mm2.06inØ5.6mm0.22inNote: two M3set screws in colararound hub shaft(will not mar shaft)MountingSurface3Hubshaft Shaft EngagementHubShaft Min. Shaft Max. ShaftHubshaft 3 w/Tether Diameter Length LengthHubshaft w/Tether 10mm, 3/8" 15mm (0.59") 20mm (0.79")12mm, 1/2" 18mm (0.71") 20mm (0.79")Radial ConnectorArea (if used). SeeConnection Diag.Code 7: ConnectorMountingSurfaceLength (L)Ø57mmØ2.24in0, 1, A, B1.5M Cable2.1mm0.08inLocation ofLocation ofStatus LED andPreset Switch on models withon models withIP64 sealing (multi-turn andPreset Switch only)15mm0.59in13mm0.51inRØ8.5mmØ0.33in14.8mm0.58inCables shown inAxial and RadialPlacementMountingSurfaceLength (L)Ø57mm2.24in2.1mm0.08inLocation ofLocation ofStatus Status LED LED andPreset Switch on models withon models withIP64 IP64 sealing sealing (multi-turn andPreset Switch only)23mm0.91in17.5mm0.69in9.0mm0.35in6, 7Conin 12/17 Pin ConnectorLength (L) Mounting Surface to RearMount (Code 3) Single-Turn Multi-Turn(0) Servo 46.5/1.83 60.2/2.37(1) Clamping 45.5/1.79 59.2/2.33(2) Square Flng 45.5/1.79 59.2/2.33(3) Hubshaft 49.9/1.96 67.1/2.64Cables shown in Axial andRadial PlacementMountingSurfaceMountingSurfaceLength (L)Ø57mm2.24inLength (L)Ø57mm2.24inJ17 Pin MS Connector, Axial9.0mm0.35in2.1mm0.08inLocation ofStatus LED andPreset Switch on models withIP64 sealing (multi-turn andPreset Switch only)K19 Pin BayonetConnector, Axial17.5mm0.69in2.81