Heavy Duty Encoder - Hengstler Encoders

yINDUSTRIAL DUTYSERIES AI25DIMENSIONSOrdering InformationTo order, complete the model number with code numbers from the table below:Code 1: Model Code 2: Bits Code 3 :Mounting Code 4: Shaft Size Code 5: Protocol Code 6: Electrical Code 7: ConnectorAI25AI25Size25AcuroAbsoluteEncoderSingle-Turn0010 10 Bit0012 12 Bit0013 13 Bit0014 14 BitMulti-Turn1212 12 Bit Multi-Turn, 12 BitSingle-Turn1213 12 Bit Multi-Turn, 13 BitSingle-Turn1214 12 Bit Multi-Turn, 14 BitSingle-TurnAvailable whenCode 4 is 0 or A0 Servo*Available whenCode 4 is 2 or C1 Clamping*Available whenCode 4 is 1 or B2 Squareflange**Available whenCode 4 is 3, 4,5 or 63 Hubshaftw/tether†* 58mm Dia.** 2.5" Square† 63mm BCw/o shaft seal (IP64)0 6 mm1 3/8"2 10 mm3 3/8" Hub Shaft4 12 mm Hubshaft5 1/2" Hubshaft6 10 mm Hub Shaftw/ shaft seal (IP67)A 6 mmB 3/8"C 10 mm6 Profibus 2 10-30 VDCEGHBus Cover3 Strain Relief Exits.Internal T-couplerincludedBus Cover2 Strain Relief Exitsand 1 M12, 5-PoleConnector (for Ticodisplay). InternalT-coupler includedBus Cover DoubleConin. InternalT-coupler includedCode 3: MountingØ42 ±0.1mm1.650.004in120°58mm2.28in10mm0.39inMountingSurfaceØ48±0.1mmØ1.89 ±0.004in45°20°120 °10mmDiameter10mm0.39in19.27mm0.76in9mm0.35inM4x50Servo6mm4mm0.16in3mm0.12in3mm0.12in1Clamping120 °M4x5M3x53mm0.12in15mm0.59inØ36mmØ1.42inMountingSurfaceØ31.75mm1.25inMountingSurface63.5mm2.5in52.4mm2.06in19.5mm ±0.30.77in ±0.013/8in Dia. Shaft7.5mm0.30in2Square Flange7mm0.28in63.5mm2.5in52.4mm2.06inØ5.6mm0.22inNote: two M3set screws in colararound hub shaft(will not mar shaft)MountingSurfaceHubshaft Shaft Engagement3 HubShaft Min. Shaft Max. ShaftHubshaft 3 w/Tether Diameter Length LengthHubshaft w/Tether 10mm, 3/8" 15mm (0.59") 20mm (0.79")12mm, 1/2" 18mm (0.71") 20mm (0.79")Radial ConnectorArea (if used). SeeConnection Diag.Length (L)58.5mm2.3inCode 7: Connector58.5mm2.3inLength (L)58.5mm2.3in76.5mm3.01inMountingSurfaceE3 Strain Relief Exits76.5mm3.01in*M12, 5-Pole Connector usedto interface Hengstler Tico 731GLCD display2 Strain Relief Exits1 M12, 5-pole Connector*MountingSurfaceHDouble Conin85.3mm3.36inLength (L) Mounting Surface to RearFor connector types E, and HMount (Code 3) Single-Turn Multi-Turn(0) Servo 63.3/2.49 72.3/2.85(1) Clamping 62.3/2.45 71.3/2.81(2) Square Flng 64.8/2.55 73.8/2.91(3) Hubshaft 72.2/2.84 81.2/3.22.71