Heavy Duty Encoder - Hengstler Encoders

yHEAVY DUTYSERIES HD25Ordering InformationTo order, complete the model number with code numbers from the table below:Code 1: ModelHD25Size 25ExtremeHeavy DutyEncoder1 Unidirectional2 Bidirectional3 Bidirectional withIndexCode 2: PPR00010024002500350040005000600100012001920200024002500256030003600500051206000625072009001000102412001250144015241600180020002048250025402600360040965000Code 3: Shaft0 3/8" Dia.Shaft withflat4 10mmDia. Shaft,with flat6 12mm Dia.Shaft7 Same asoption 0with 4 hole2.00” B.C.Note:10 foot Cable Assemblies with MS Connector108594-0010 6 Pin MS, Cable Assy. For Use with Single Ended Outputs108595-0010 7 Pin MS, Cable Assy. For Use with Single Ended Outputs108596-0010 7 Pin MS, Cable Assy. For Use with DifferentialLine Driver w/o Index Outputs1400635-0010 10 Pin MS, Cable Assy. For Use with DifferentialLine Driver with Index Outputs109209-0010 NEMA4 10 pin MS, Cable Assy. For use withdifferential line driver with index outputsMating Connectors (no cable)6 pin, style MS3106A-14S-6S (MCN-N4)7 pin, style MS3106A-16S-1S (MCN-N5)10 pin, style MS3106A-18-1S (MCN-N6)10 pin, NEMA 4 style (604505 & 604506)Code 4: ElectricalOrdering Information0 5-26V in, 5-26V 1 6 Pin ConnectorOpen Collector out 3 7 Pin Connector(7273)5 10 Pin Connector2 5-26V in, 5-26VPush-Pull out9 5 Pin M12 ConnectorF 5-26V in, 5-26VD 18" Sealed CableOpen Collector out E 3’ Sealed Cable(2222)F 6’ Sealed CableG 5-26V in, 5-26V G 10’ Sealed CableOpen Collector outwith 2.2 kΩ PullupsH 15’ Sealed Cable(2222)P 5m Sealed CableAvailable when: Code1 is 1, 2 and Code 5is 3,5 or D through P,or Code 1 is 3 andcode 5 is 5 or Dthrough P:3 5-26V in, 5-26VDifferential LineDriver out (7272)4 5-26V in, 5VDifferential LineDriver out (7272)6 5-15V in, 5-15VDifferential LineDriver out (4469)Code 5: Termination*Note: Available ATEX CertifiedOptionsATEX Type 1: ATEX Certified;5V in, 5V out onlyATEX Type 2: ATEX Certified;7-26V in, 7-26V outATEX Type 3: ATEX Certified;7-26V in, 5V outATEX Type 4: ATEX Certified;5-15V in, 5-15V outNOTE: ATEX voltages replacethose shown in Code 4.† NOTE: Simultaneous useof redundant outputs mayvoid ATEX certification.Consult factory fordetails.Code 6: Options0 No Options1 Nickel Finish Housing2 Stainless Steel Housing3 Redundant Outputs (Dual ConnectorHousing). See † NOTE4 Nickel Finish Housing with RedundantOutputs. See † NOTE5 Stainless Steel Housing withRedundant Outputs. See † NOTEA Same as "0" w/ ATEX Type 1B Same as "1" w/ ATEX Type 1C Same as "2" w/ ATEX Type 1D Same as "3" w/ ATEX Type 1. See †NOTEE Same as "4" w/ ATEX Type 1. See †NOTEF Same as "5" w/ ATEX Type 1. See †NOTEAvailable when Code 4 is 0-3, F or GG Same as "0" w/ ATEX Type 2H Same as "1" w/ ATEX Type 2I Same as "2" w/ ATEX Type 2J Same as "3" w/ ATEX Type 2. See †NOTEK Same as "4" w/ ATEX Type 2. See †NOTEL Same as "5" w/ ATEX Type 2. See †NOTEAvailable when Code 4 is 4M Same as "0" w/ ATEX Type 3N Same as "1" w/ ATEX Type 3O Same as "2" w/ ATEX Type 3P Same as "3" w/ ATEX Type 3. See †NOTEQ Same as "4" w/ ATEX Type 3. See †NOTER Same as "5" w/ ATEX Type 3. See †NOTEAvailable when Code 4 is 6:S Same as 0, w/ATEX Type 4T Same as 1, W/ATEX Type 4U Same as 2, w/ATEX Type 4V Same as 3, w/ATEX Type 4. See †NOTEW Same as 4, w/ATEX Type 4. See †NOTEY Same as 5, w/ATEX Type 4. See †NOTEDIMENSIONS inches [mm]Standard Housing0.54 [13.7]0.30 [7.6]2.65 [67.3]2XDual Redundant Outputs1.95[49.5]Cable Exit0.86 [21.8]1.95[49.5]Flat 0.70 x 0.018[17.8 x 0.46]ShaftØ0.37 [9.5]1.95[49.5]2.95[74.9]0.70 [17.8]0.018 [.46]FlatØ1.25[31.8]2.064 [52.4]2X1.54[39.1]1.91[48.5]0.91 max.[23]4x R0.21[5.3]4x Ø0.22[5.6]10-32 UNF 2B x 0.38" deepon 1.875" bolt circleShaftØ0.37 [9.5]4x R0.21[5.3]4x Ø0.22[5.6]1.54[39.1]1.95[49.5]0.30 [7.6]4X #4-40 X .250 MIN.Ø2.00 B.CWith 4 hole 2.00” B.C.1.07