Untitled - Flannery Plant Hire

More documents

Recommendations

Info

OPERATOR'S STATIONADJUSTING THE SEATSeat Height and Angle AdjustmentSeat height adjustment range is 60 mm (2.4 in) withsteps every 15 mm (0.6 in) (5 positions in total). Moreover,the height of the front part and the rear part of theseat are adjusted independently, thus allowing the angleof the seat to be adjusted.CAUTION: Avoid possible injury while operatinglever (1). When pushing down lever (1), do notgrab it. Fingers may be pinched between lever (1)and the seat stand. Be sure to push on the upperface of lever (1).Use lever (1) to adjust the seat height and/or seat angleas follows:• To adjust the front part of the seat:Push down lever (1) while sitting on the seat, and applyor remove body weight to obtain the desired height.When the desired height is obtained, release lever (1).• To adjust the rear part of the seat:Pull up lever (1) while sitting on the seat, and apply orremove body weight to obtain the desired height.When the desired height is obtained, release lever (1).Caution: Possibility ofpinched fingersPush down with thepalm.SS-74751Console and Seat Fore-aft AdjustmentPull lever (2) to the right to adjust the seat and both rightand left consoles to desired distance from the travelpedals and levers. Release lever to lock seat and consolesinto position.NOTE: Seat and console fore-aft adjustment range is120 mm (4.7 in) with steps every 20 mm (0.8in).243M178-02-066Seat Fore-Aft AdjustmentPull lever (3) to the right to unlock the seat from bothconsoles. With lever held to the right, slide the seat tothe desired distance from pilot control levers. Releasethe lever.NOTE: Seat fore-aft adjustment range is 160 mm (6.3in) with steps every 16 mm (0.8 in).Suspension AdjustmentTurn knob (4) clockwise to increase suspension stiffness.Turn knob counterclockwise to decrease suspensionstiffness.Backrest AdjustmentPull up lever (5) to release backrest lock. Move backrestto the desired position and release the lever.1-59
OPERATOR'S STATIONArmrest AdjustmentArmrest (6) can be pulled upright by hand to get on andoff the machine easily.The angle of armrest (6) can be adjusted to the desiredposition by turning adjusting dial (7) located on the bottomof armrest (6).6860 degreesHeadrestHeadrest height and angle can be adjusted.Pull headrest (8) upward or push downward to the desiredposition. (Height adjustment range: 50 mm (2.0 in))Headrest (8) can be adjusted 60 degrees forward fromthe upright position. Move headrest by hands to the desiredangle.7M1G6-01-017SEAT WITH A BUILT-IN HEATER (Optional)The heater installed inside the seat activates by operatingseat heater switch (1) on the optional equipmentcontrol switch panel.NOTE: Depending on what kinds of optional equipmentsare installed, the switch button functionmay differ. Use the switch only after confirmingthe kinds of the installed optional equipment.1M178-01-1201M1G6-01-0191-60
Page 4 and 5:
MACHINE NUMBERSThe manufacturing No
Page 6 and 7:
MACHINE NUMBERSTRANSMISSIONTYPE:MFG
Page 8 and 9:
CONTENTSMACHINE NUMBERSSAFETYRecogn
Page 10 and 11:
CONTENTSPeriodic Replacement of Par
Page 12 and 13:
SAFETYRECOGNIZE SAFETY INFORMATION!
Page 14 and 15:
SAFETYWEAR PROTECTIVE CLOTHING!" We
Page 16 and 17:
SAFETYUSE HANDHOLDS AND STEPS!" Fal
Page 18 and 19:
OPERATE ONLY FROM OPERATOR’S SEAT
Page 20 and 21:
PROVIDE SIGNALS FOR JOBS INVOLVINGM
Page 22 and 23:
SAFETYAVOID INJURY FROM ROLLAWAYACC
Page 24 and 25:
SAFETYKEEP PERSONNEL CLEAR FROM WOR
Page 26 and 27:
SAFETYDIG WITH CAUTION!" Accidental
Page 28 and 29:
SAFETYPARK MACHINE SAFELYTo avoid a
Page 30 and 31:
SAFETYPRACTICE SAFE MAINTENANCETo a
Page 32 and 33:
SAFETYPREVENT PARTS FROM FLYING!" T
Page 34 and 35:
SAFETYAVOID HIGH-PRESSURE FLUIDS!"
Page 36 and 37:
SAFETYCheck Heat Shields:!" Damaged
Page 38 and 39:
SAFETYAVOID HEATING NEAR PRESSURIZE
Page 40 and 41:
HANDLE CHEMICAL PRODUCTS SAFELYSAFE
Page 42 and 43:
SAFETY SIGNS/Europe/Asia/Middle and
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
COMPONENTS NAMECOMPONENTS NAME1- Bu
Page 50 and 51:
OPERATOR'S STATIONSTEERING COLUMN C
Page 52 and 53:
OPERATOR'S STATIONBRAKE PEDAL12CAUT
Page 54 and 55:
OPERATOR'S STATIONSHIFT LEVER1Trave
Page 56 and 57: OPERATOR'S STATIONBRAKE SWITCHBrake
Page 58 and 59: OPERATOR'S STATIONWIPER SWITCHTurn
Page 60 and 61: COOLANT TEMPERATURE GAUGEEngine coo
Page 62 and 63: OPERATOR'S STATIONALTERNATOR INDICA
Page 64 and 65: TRIP METER(TRIP METER 1 AND TRIP ME
Page 66 and 67: OPERATOR'S STATIONResetting Set-Hou
Page 68 and 69: OPERATOR'S STATIONSWITCH PANEL1- En
Page 70 and 71: OPERATOR'S STATIONWORK LIGHT SWITCH
Page 72 and 73: OPERATOR'S STATIONSWITCH PANEL (Opt
Page 74 and 75: OPERATOR'S STATIONHORN SWITCHHorn s
Page 76 and 77: OPERATOR'S STATIONCAB LIGHTTurn the
Page 78 and 79: OPERATOR'S STATIONSWING LOCK LEVERT
Page 80 and 81: OPERATOR'S STATIONAUTO AIR CONDITIO
Page 82 and 83: OPERATOR'S STATION!" Temperature Co
Page 84 and 85: OPERATOR'S STATIONCOOLING OPERATION
Page 86 and 87: OPERATOR'S STATIONAUTO AIR CONDITIO
Page 88 and 89: OPERATOR'S STATIONControl Panel Des
Page 90 and 91: OPERATOR'S STATION!" Circulation Mo
Page 92 and 93: OPERATOR'S STATIONDEFROSTER OPERATI
Page 94 and 95: OPERATOR'S STATIONCAB HEATER (Optio
Page 96 and 97: OPERATOR'S STATIONDEFROSTER OPERATI
Page 98 and 99: OPERATOR'S STATIONStation Presettin
Page 100 and 101: OPERATOR'S STATIONStation Presettin
Page 102 and 103: CLOSING UPPER FRONT WINDOWOPERATOR'
Page 104 and 105: OPERATOR'S STATIONOPENING/CLOSING O
Page 108 and 109: ADJUSTING THE AIR-SUSPENSION SEAT(O
Page 110 and 111: OPERATOR'S STATIONSEAT BELT1 2CAUTI
Page 112 and 113: OBSERVE ENGINE OPERATION CLOSELYBRE
Page 114 and 115: INSPECT MACHINE DAILY BEFORE START-
Page 116 and 117: STARTING THE ENGINE IN ORDINARY TEM
Page 118 and 119: CHECK INSTRUMENTS AFTER STARTINGOPE
Page 120 and 121: OPERATING THE ENGINEDisconnecting t
Page 122 and 123: TRAVELINGCorrect machine operation
Page 124 and 125: PrecautionsDRIVING THE MACHINE1. Ch
Page 126 and 127: DRIVING THE MACHINE1. Even after th
Page 128 and 129: TRAVELING IN WATER OR ON SOFTTERRAI
Page 130 and 131: DRIVING THE MACHINEEMERGENCY PARKIN
Page 132 and 133: CONTROL LEVER (ISO PATTERN)OPERATIN
Page 134 and 135: OPERATING THE MACHINESTEERING WHEEL
Page 136 and 137: OPERATING THE MACHINEWarming-up the
Page 138 and 139: OPERATING THE MACHINEAUTO-IDLEWith
Page 140 and 141: OPERATING THE MACHINEChanging Auto-
Page 142 and 143: OPERATING THE MACHINEPOWER MODEOne
Page 144 and 145: PRECAUTIONS FOR OPERATIONSOPERATING
Page 146 and 147: TRAVELING/OPERATING THE MACHINE ONA
Page 148 and 149: OPERATING THE MACHINEEXCAVATION•
Page 150 and 151: OPERATING THE MACHINEGRADINGWhile o
Page 152 and 153: OPERATING THE MACHINEEMERGENCY BOOM
Page 154 and 155: OVERNIGHT STORAGE INSTRUCTIONSOPERA
Page 156 and 157:
GENERAL TRANSPORTATION HINTSTRANSPO
Page 158 and 159:
TRANSPORTATION2. Load the machine s
Page 160 and 161:
TRANSPORTATIONTOWING MACHINEWhen to
Page 162 and 163:
MAINTENANCECORRECT MAINTENANCE AND
Page 164 and 165:
MAINTENANCELAYOUTMonoblock boomBuck
Page 166 and 167:
MAINTENANCEMaintenance Guide TableS
Page 168 and 169:
MAINTENANCEHOOD AND ACCESS COVERS11
Page 170 and 171:
MAINTENANCEMAINTENANCE GUIDEA. GREA
Page 172 and 173:
F. HYDRAULIC SYSTEM (See Page 7-37)
Page 174 and 175:
Brand Names of Recommended GreaseWh
Page 176 and 177:
MAINTENANCEA. GREASINGFront Joint P
Page 178 and 179:
MEMOMAINTENANCE....................
Page 180 and 181:
MAINTENANCESwing Internal Gear ---
Page 182 and 183:
MAINTENANCEPropel Shaft (Front and
Page 184 and 185:
MAINTENANCEB. ENGINEEngine Oil Leve
Page 186 and 187:
MAINTENANCE11. Open the right and l
Page 188 and 189:
MAINTENANCESwing Reduction GearChec
Page 190 and 191:
MAINTENANCEFront AxleCAUTION: The c
Page 192 and 193:
MAINTENANCEFront and Rear Hub Reduc
Page 194 and 195:
MAINTENANCECheck Brake Accumulator1
Page 196 and 197:
MAINTENANCEE. TIRETire/SizeUse tire
Page 198 and 199:
MAINTENANCEF. HYDRAULIC SYSTEMINSPE
Page 200 and 201:
REPLACEMENT OF HYDRAULIC OIL ANDFIL
Page 202 and 203:
MAINTENANCEDrain Hydraulic Oil Tank
Page 204 and 205:
MAINTENANCEBleed Air from Hydraulic
Page 206 and 207:
MAINTENANCEClean the Suction Filter
Page 208 and 209:
MAINTENANCEReplace Full-Flow Filter
Page 210 and 211:
MAINTENANCEReplace Air Breather Ele
Page 212 and 213:
MAINTENANCECheck Hoses and Lines---
Page 214 and 215:
MAINTENANCETable 2. LinesInterval(h
Page 216 and 217:
MAINTENANCEMetal Face Seal Fittings
Page 218 and 219:
MAINTENANCENOTE: Take precautions f
Page 220 and 221:
MAINTENANCEBleed Air from Fuel Syst
Page 222 and 223:
MAINTENANCEClean Feed Pump Strainer
Page 224 and 225:
MAINTENANCEH. AIR CLEANERClean Air
Page 226 and 227:
MAINTENANCEI. COOLING SYSTEMCoolant
Page 228 and 229:
MAINTENANCEChange Coolant--- twice
Page 230 and 231:
MAINTENANCEJ. ELECTRICAL SYSTEMIMPO
Page 232 and 233:
MAINTENANCEElectrolyte Level Check
Page 234 and 235:
MAINTENANCEREPLACING FUSESIf any el
Page 236 and 237:
MAINTENANCEK. MISCELLANEOUS1 4 5Che
Page 238 and 239:
MAINTENANCEChange BucketCAUTION: Wh
Page 240 and 241:
MAINTENANCEAdjust the Bucket Linkag
Page 242 and 243:
MAINTENANCEClean and Replace Air Co
Page 244 and 245:
MAINTENANCECheck the Air Conditione
Page 246 and 247:
MAINTENANCECheck Injection Nozzle--
Page 248 and 249:
MAINTENANCECheck Tightening Torque
Page 250 and 251:
MAINTENANCECheck Tightening Torque
Page 252 and 253:
MAINTENANCE1. Retighten the engine
Page 254 and 255:
MAINTENANCE10. Retighten the swing
Page 256 and 257:
MAINTENANCE17. Retighten propel sha
Page 258 and 259:
MEMOMAINTENANCE....................
Page 260 and 261:
MEMOMAINTENANCE UNDER SPECIAL ENVIR
Page 262 and 263:
STORAGEREMOVING THE MACHINE FROM ST
Page 264 and 265:
TROUBLESHOOTING3. Engine is hard to
Page 266 and 267:
TROUBLESHOOTINGProblem Cause Soluti
Page 268 and 269:
TROUBLESHOOTINGBrakeProblem Cause S
Page 270 and 271:
TROUBLESHOOTING8. Engine SpeedProbl
Page 272 and 273:
SPECIFICATIONSSpecificationsZAXIS13
Page 274 and 275:
Page 276 and 277:
SPECIFICATIONSWORKING RANGESZAXIS13
Page 278 and 279:
SPECIFICATIONSSPECIFICATIONSZAXIS16
Page 280 and 281:
SpecificationsZAXIS160W (FRONT BLAD
Page 282 and 283:
Page 284 and 285:
BUCKET TYPES AND APPLICATIONSZAXIS1
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
SPECIFICATIONSWORKING RANGESZAXIS18
Page 292 and 293:
SPECIFICATIONSSPECIFICATIONSZAXIS21
Page 294 and 295:
SpecificationsZAXIS210W (FRONT BLAD
Page 296 and 297:
Page 298 and 299:
BUCKET TYPES AND APPLICATIONSZAXIS2
Page 300 and 301:
OPTIONAL ATTACHMENTS AND DEVICES"#
Page 302 and 303:
OPTIONAL ATTACHMENTS AND DEVICESSta
Page 304 and 305:
ATTACHMENT PEDAL (BREAKER)(Optional
Page 306 and 307:
OPTIONAL ATTACHMENTS AND DEVICES•
Page 308 and 309:
ATTACHMENT PEDAL(HYDRAULIC CRUSHER)
Page 310 and 311:
OPTIONAL ATTACHMENTS AND DEVICESELE
Page 312 and 313:
OPTIONAL ATTACHMENTS AND DEVICESIf
Page 314 and 315:
OPTIONAL ATTACHMENTS AND DEVICESADD
Page 316 and 317:
MEMOOPTIONAL ATTACHMENTS AND DEVICE
Page 318 and 319:
INDEXGGeneral Precautions for Cab..
show all

Untitled - Flannery Plant Hire

Create successful ePaper yourself

Delete template?

Save as template?