Full-Custom Layout of an SRAM-Based FPGA - University of Toronto

More documents

Recommendations

Info

The following two circuits are the Dflip-flops to be used. The second Dflip-flop has set and reset signal need for the register inside the LE. The other Dflip-flop is to be used in the shift registers of the programming logic. The following two figures are the simulations of the Dflip-flop and Dflip-flop with set and reset, respectively.
Set and Reset Selection: The following figure is the set and reset logic. The simulations show the set and reset logic working. The second simulations show the reset being selected.
Page 1 and 2: UNIVERSITY OF TORONTO ECE1388 VLSI
Page 3 and 4: There has been a great deal of stud
Page 5 and 6: The final design contains 48 pins.
Page 7 and 8: [1] V. Betz, J. Rose, and A. Marqua
Page 9 and 10: 1. FPGA Design The purpose of this
Page 12 and 13: 3. Logic Element The logic element
Page 15 and 16: 4. Routing Routing consists of the
Page 18 and 19: 5. Programming Circuitry We are goi
Page 20 and 21: Caculate SRAMs in logic Block: Logi
Page 22 and 23: Appendix C Cell Circuit Design Repo
Page 24 and 25: Each wire is connected to another t
Page 26 and 27: There are two new components in thi
Page 28 and 29: Pass transistors that connect outpu
Page 30 and 31: Since this connection box only cont
Page 32 and 33: Feedback Buffer: The feedback buffe
Page 36 and 37: NAND:
Page 38 and 39: The following two figures the circu
Page 41 and 42: Schematic Description of program_ro
Page 43 and 44: Figure 2: program_col Schematic Fig
Page 45 and 46: Figure 5: Clock Input to program_ro
Page 47 and 48: Figure 9: Output of Program Figure
Page 53 and 54: Figure 21: Output of Program_data F
Page 55 and 56: Appendix D Full Schematic Design Re
Page 57 and 58: To test the individual tile, and th
Page 59 and 60: To test the tile, we implement the
Page 61: The first figure shows the programm
Page 64 and 65: The three by three array of tiles c
Page 66 and 67: tiles, and then an array of four by
Page 68 and 69: Appendix E Layout of the Cells Repo
Page 70 and 71: The SRAM cell is one our base cells
Page 72 and 73: Switch box interconnects the wiring
Page 74 and 75: Inverters are standard design, as w
Page 76 and 77: 4-to-1 multiplexer is made out of 3
Page 78 and 79: Connection Box Bottom Connection bo
Page 80 and 81: The Input_to_LE cell was designed u
Page 82 and 83: All the cells passed DRC and LVS. H
Page 84 and 85:
connection_box_right: @(#)$CDS: LVS
Page 86 and 87:
connect_box_bottom: @(#)$CDS: LVS v
Page 88 and 89:
Switchbox: @(#)$CDS: LVS version 4.
Page 90 and 91:
prunenet.out: prunedev.out: audit.o
Page 92 and 93:
Logic Element The Logic Element cel
Page 94 and 95:
Connection Right Block The Connecti
Page 96 and 97:
Switch Block Layout Figure Tile Blo
Page 98 and 99:
Program Row Tile Block The Program
Page 100 and 101:
Program Column Tile Block The Progr
Page 103 and 104:
FPGA Top-Level Schematic:
Page 105 and 106:
The net-lists match. layout schemat
show all

Full-Custom Layout of an SRAM-Based FPGA - University of Toronto

Create successful ePaper yourself

Delete template?

Save as template?