FR-A701 INSTRUCTION MANUAL (Applied) - Automation Systems ...

More documents

Recommendations

Info

1OUTLINEMethod of removal and reinstallation ofthe front cover1.3 Method of removal and reinstallation of the front cover•Removal of the operation panel1) Loosen the two screws on the operation panel.(These screws cannot be removed.)2) Push the left and right hooks of the operation paneland pull the operation panel toward you to remove.When reinstalling the operation panel, insert it straight to reinstall securely and tighten the fixed screws of theoperation panel.•Removal of the front cover1) Remove installation screws on the front cover1 to remove the front cover 1.2) Loosen the installation screws of thefront cover 2.Front cover 1Front cover 23) Pull the front cover 2 toward you to remove by pushing an installation hook on the right sideusing left fixed hooks as supports.Installation hook5
Method of removal and reinstallation ofthe front cover•Reinstallation of the front cover1) Insert the two fixed hooks on the left side of thefront cover 2 into the sockets of the inverter.2) Using the fixed hooks as supports, securely press thefront cover 2 against the inverter.(Although installation can be done with the operationpanel mounted, make sure that a connector issecurely fixed.)Front cover 2 Front cover 23) Fix the front cover 2 with the installation screws. 4) Fix the front cover 1 with the installationscrews.Front cover 2Front cover 1REMARKS· For the 55K, the front cover 1 is separated into two parts.CAUTION1. Fully make sure that the front cover has been reinstalled securely. Always tighten the installation screws of the front cover.2. The same serial number is printed on the capacity plate of the front cover and the rating plate of the inverter. Beforereinstalling the front cover, check the serial numbers to ensure that the cover removed is reinstalled to the inverter from whereit was removed.6
Page 1 and 2: INVERTERFR-A701INSTRUCTION MANUAL (
Page 3 and 4: CONTENTS1 OUTLINE 11.1 Product chec
Page 5 and 6: 4.6.4 Setting of the electronic gea
Page 7 and 8: 4.18.4 Overspeed detection (Pr. 374
Page 9 and 10: 5.5.5 Motor rotates in opposite dir
Page 11 and 12: MEMO
Page 13 and 14: Product checking and parts identifi
Page 15: Inverter and peripheral devices1.2.
Page 19 and 20: Installation of the inverter and en
Page 25 and 26: Terminal connection diagram2.1 Term
Page 27 and 28: Main circuit terminal specification
Page 33 and 34: Control circuit specifications2.3 C
Page 35 and 36: Control circuit specifications(2) O
Page 37 and 38: Control circuit specifications4)Sin
Page 39 and 40: Control circuit specifications2.3.4
Page 41 and 42: Connection of motor with encoder (v
Page 49 and 50: EMC and leakage currents3.1 EMC and
Page 51 and 52: EMC and leakage currents3.1.2 EMC m
Page 53 and 54: EMC and leakage currents3.1.3 Power
Page 55 and 56: Power-off and magnetic contactor (M
Page 57 and 58: Precautions for use of the inverter
Page 59 and 60: Failsafe of the system which uses t
Page 61 and 62: MEMO50
Page 63 and 64: Operation panel (FR-DU07)4.1 Operat
Page 65 and 66: Operation panel (FR-DU07)4.1.3 Chan
Page 67 and 68:
Parameter listParameter ListFunctio
Page 69 and 70:
Page 71 and 72:
Parameter listFunctionParameter Nam
Page 73 and 74:
Page 75 and 76:
Parameter listFunctionParameter Nam
Page 77 and 78:
Page 79 and 80:
Parameters according to purposes4.3
Page 81 and 82:
4.21.4 Response level of analog inp
Page 83 and 84:
Control mode4.3.1 What is vector co
Page 85 and 86:
Control mode(1) Speed controlSpeed
Page 87 and 88:
Control mode(3) Vector control test
Page 89 and 90:
Control mode• Terminal 4 function
Page 91 and 92:
Speed control by real sensorless ve
Page 93 and 94:
Page 95 and 96:
Page 98 and 99:
4PARAMETERSSpeed control by real se
Page 100 and 101:
Page 102 and 103:
4PARAMETERS(5) Manual input speed c
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
4PARAMETERS(4) Setting torque bias
Page 112 and 113:
Page 114 and 115:
4PARAMETERSTorque control by real s
Page 116 and 117:
4PARAMETERS(3) Operation example (w
Page 118 and 119:
Page 120 and 121:
4PARAMETERS(3) Torque command using
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
4PARAMETERSPosition control by vect
Page 128 and 129:
Page 130 and 131:
4PARAMETERS(1) Setting of position
Page 132 and 133:
4PARAMETERS(3) Selection of clear s
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
4PARAMETERSAdjustment of real senso
Page 140 and 141:
4PARAMETERSAdjust the output torque
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
4PARAMETERSLimit the output frequen
Page 154 and 155:
4PARAMETERS(3) Base frequency volta
Page 156 and 157:
4PARAMETERSSet V/F patternPr. 14Set
Page 158 and 159:
4PARAMETERS4.10.4 Adjustable 5 poin
Page 160 and 161:
4PARAMETERSFrequency setting by ext
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
4PARAMETERS4.12 Setting of accelera
Page 168 and 169:
4PARAMETERSSetting of acceleration/
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
4PARAMETERS(2) Optimum acceleration
Page 176 and 177:
4PARAMETERS4.13 Selection and prote
Page 178 and 179:
4PARAMETERSSelection and protection
Page 180 and 181:
4PARAMETERS4.13.2 Applied motor (Pr
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
4PARAMETERSMotor brake and stop ope
Page 198 and 199:
4PARAMETERS(5) Brake operation sele
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
4PARAMETERS• Position loop gain (
Page 216 and 217:
4PARAMETERS• Pr. 399 Orientation
Page 218 and 219:
4PARAMETERSFunction assignment of e
Page 220 and 221:
4PARAMETERS4.15.2 Inverter output s
Page 222 and 223:
Page 224 and 225:
4PARAMETERS4.15.5 Magnetic flux dec
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
4PARAMETERS(3) Forward rotation and
Page 232 and 233:
Page 234 and 235:
4PARAMETERS4.15.8 Output current de
Page 236 and 237:
4PARAMETERS4.15.10 Remote output fu
Page 238 and 239:
4PARAMETERSMonitor display and moni
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
4PARAMETERSOperation selection at p
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
4PARAMETERS(6) Power failure decele
Page 258 and 259:
4PARAMETERS⋅⋅⋅⋅Operation se
Page 260 and 261:
4PARAMETERS4.18.3 Input/output phas
Page 262 and 263:
4PARAMETERSEnergy saving operation
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
4PARAMETERSMotor noise, EMI measure
Page 270 and 271:
4PARAMETERSFrequency/torque setting
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
4PARAMETERS4.21.4 Response level of
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
Page 286 and 287:
4PARAMETERS(6) Adjustment method of
Page 288 and 289:
4PARAMETERSc) Method to adjust torq
Page 290 and 291:
4PARAMETERS(2) Disconnected PU dete
Page 292 and 293:
4PARAMETERS4.22.3 Reverse rotation
Page 294 and 295:
4PARAMETERSSelection of operation m
Page 296 and 297:
Page 298 and 299:
4PARAMETERS(6) PU/external combined
Page 300 and 301:
4PARAMETERS(10) Switching of operat
Page 302 and 303:
4PARAMETERS4.23.2 Operation mode at
Page 304 and 305:
Page 306 and 307:
Page 308 and 309:
4PARAMETERS4.24 Communication opera
Page 310 and 311:
4PARAMETERS4.24.2 Wiring and arrang
Page 312 and 313:
4PARAMETERSCommunication operation
Page 314 and 315:
Page 316 and 317:
Page 318 and 319:
Page 320 and 321:
4PARAMETERS(8) Instructions for the
Page 322 and 323:
4PARAMETERS(9) Setting items and se
Page 324 and 325:
Page 326 and 327:
Page 328 and 329:
Page 330 and 331:
4PARAMETERS(5) Message format types
Page 332 and 333:
Page 334 and 335:
Page 336 and 337:
Page 338 and 339:
Page 340 and 341:
4PARAMETERS4.25 Special operation a
Page 342 and 343:
4PARAMETERSSpecial operation and fr
Page 344 and 345:
Page 346 and 347:
Page 348 and 349:
Page 350 and 351:
Page 352 and 353:
Page 354 and 355:
4PARAMETERS(1) Load torque high spe
Page 356 and 357:
4PARAMETERS(2) Limit the frequency
Page 358 and 359:
Page 360 and 361:
Page 362 and 363:
4PARAMETERS4.25.7 Regeneration avoi
Page 364 and 365:
4PARAMETERSUseful functions4.26 Use
Page 366 and 367:
4PARAMETERS(1) Life alarm display a
Page 368 and 369:
4PARAMETERSUseful functions4.26.3 M
Page 370 and 371:
4PARAMETERSUseful functions(3) Sett
Page 372 and 373:
4PARAMETERSSetting of the parameter
Page 374 and 375:
4PARAMETERSSetting of the parameter
Page 376 and 377:
4PARAMETERSAll parameter clear4.29
Page 378 and 379:
4PARAMETERSParameter copy and param
Page 380 and 381:
4PARAMETERSCheck and clear of the f
Page 382 and 383:
5 PROTECTIVE FUNCTIONSThis chapter
Page 384 and 385:
List of fault or alarm display5.2 L
Page 386 and 387:
Causes and corrective actionsOperat
Page 388 and 389:
Page 390 and 391:
Page 392 and 393:
Page 394 and 395:
Page 396 and 397:
Page 398 and 399:
Page 400 and 401:
Correspondences between digital and
Page 402 and 403:
Check first when you have troubles5
Page 404 and 405:
6 PRECAUTIONS FORMAINTENANCE AND IN
Page 406 and 407:
Inspection item6.1.3 Daily and peri
Page 408 and 409:
Inspection item6.1.6 CleaningAlways
Page 410 and 411:
(2) Smoothing capacitorsInspection
Page 412 and 413:
Measurement of main circuit voltage
Page 414 and 415:
Measurement of main circuit voltage
Page 416 and 417:
7 SPECIFICATIONSThis chapter provid
Page 418 and 419:
Rating•400V classType FR-A741-K 5
Page 420 and 421:
Common specifications7.2 Common spe
Page 422 and 423:
Outline dimension drawings•FR-A72
Page 424 and 425:
Outline dimension drawings•FR-A72
Page 426 and 427:
Outline dimension drawings7.3.2 Ded
Page 428 and 429:
Outline dimension drawings• Dedic
Page 430 and 431:
Installation of the heatsink portio
Page 432 and 433:
APPENDICESThis chapter provides the
Page 434 and 435:
Appendix 2 Control mode-based param
Page 436 and 437:
ParameterNameInstructionCode * 1Rea
Page 438 and 439:
Page 440 and 441:
Page 442 and 443:
Page 444 and 445:
Parameter423NamePosition feed forwa
Page 446 and 447:
Parameter500NameInstructionCode * 1
Page 448 and 449:
Page 450 and 451:
ParameterC16(919)C17(919)C18(920)C1
show all

FR-A701 INSTRUCTION MANUAL (Applied) - Automation Systems ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?