EMCO WinNC SINUMERIK 810/820 T Software Description ...

More documents

Recommendations

Info

EMCO WINNC SINUMERIK 810/820 TBASICSZero OffsetWith EMCO lathes the machine zero "M" lies onthe rotating axis and on the end face of the spindleflange. This position is unsuitable as a startingpoint for dimensioning. With the so-called zerooffset the coordinate system can be moved to asuitable point in the working area of the machine.In the setting data zero offset are four adjustable zerooffsets available.0 :Zero offset from the machine zero point to theworkpiece zero pointWhen you define a value in the offset register, thisvalue will be considered with call up in program (G54- G57) and the coordinate zero point will be shiftedfrom the machine zero M to the workpiece zero W.The workpiece zero point can be shifted within aprogram with "G58, G59 - programmable zerooffset" in any number.More informations see in command description G58,G59.Coordinate SystemIncremental;;=88:;;88=:AbsoluteAbsolute coordinates relate to a fixed position,incremental coordinates to the tool position.The X and -X in brackets are valid for the PCTURN 50/55 because the tool is in front of theturning centre at this machine.The X coordinate lies in the direction of the crossslide, the Z coordinate lies in the direction of thelongitudinal slide.Coordinate values in minus direction describemovements of the tool system towards the workpiece,values in plus direction away from the workpiece.Coordinate System with AbsoluteProgrammingThe origin of the coordinate system lies at the machinezero "M" or at the workpiece zero "W" following aprogrammed zero offset.All target points are described from the origin of thecoordinate system by the indication of the respectiveX and Z distances.X distances are indicated as the diameter (asdimensioned on the drawing)Coordinate System with IncrementalProgrammingThe origin of the coordinate system lies at the toolmount reference point "N" or at the cutting tip after atool call-up.With incremental programming the actual pathes ofthe tool (from point to point) are described.X will be entered as radius.B 2
EMCO WINNC SINUMERIK 810/820 TBASICSInput of theZero Offset:LQ1&Ã6LQXPHULNÃ7ÃFÃ(0&2Ã [$8720$7,&6(77,1*'$7$ÃÃ=(52Ã2))6(7ÃÃÃÃÃÃÃÃÃÃÃÃÃ*=(52Ã2))6(7;
Page 2 and 3: EMCO WINNC SINUMERIK 810/820 TPREFA
Page 4 and 5: EMCO WINNC SINUMERIK 810/820 TCONTE
Page 6 and 7: EMCO WINNC SINUMERIK 810/820 TKEY D
Page 13: EMCO WINNC SINUMERIK 810/820 TBASIC
Page 17 and 18: EMCO WINNC SINUMERIK 810/820 TBASIC
Page 19 and 20: EMCO WINNC SINUMERIK 810/820 TBASIC
Page 21 and 22: EMCO WINNC SINUMERIK 810/820 TOPERA
Page 33 and 34: EMCO WINNC SINUMERIK 810/820 TPROGR
Page 65 and 66:
EMCO WINNC SINUMERIK 810/820 T@-COD
Page 67 and 68:
EMCO WINNC SINUMERIK 810/820 T@-COD
Page 69 and 70:
EMCO WINNC SINUMERIK 810/820 TSURVE
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
EMCO WINNC SINUMERIK 810/820 TALARM
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
show all

EMCO WinNC SINUMERIK 810/820 T Software Description ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?