EMCO WinNC SINUMERIK 810/820 T Software Description ...

More documents

Recommendations

Info

EMCO WINNC SINUMERIK 810/820 TALARMS / MESSAGES8104 Fatal system error ACsee 8101.8105 Fatal init error ACsee 8101.8106 No PC-COM card foundCause: PC-COM board can not be accessed (ev.not mounted).Remedy: Mount board, adjust other address withjumper8107 PC-COM card not workingsee 8106.8108 Fatal error on PC-COM cardsee 8106.8109 Fatal error on PC-COM cardsee 8106.8110 PC-COM init message missingCause: Internal errorRemedy: Restart software or reinstall when necessary,report to EMCO, if repeatable.8111 Wrong configuration of PC-COMsee 8110.8113 Invalid data (pccom.hex)see 8110.8114 Programming error on PC-COMsee 8110.8115 PC-COM packet acknowledge missingsee 8110.8116 PC-COM startup errorsee 8110.8117 Fatal init data error (pccom.hex)see 8110.8118 Fatal init error ACsee 8110, ev. insufficient RAM memory8119 PC interrupt no. not validCause: The PC interrupt number can not be used.Remedy: Find out free interrupt number in the Windows95system control (allowed: 5,7,10,11, 12, 3, 4 und 5) and enter this number inWinConfig.8120 PC interrupt no. unmaskablesee 81198121 Invalid command to PC-COMCause: Internal error or defective cableRemedy: Check cables (screw it); Restart softwareor reinstall when necessary, report toEMCO, if repeatable.8122 Internal AC mailbox overrunCause: Internal errorRemedy: Restart software or reinstall when necessary,report to EMCO, if repeatable.8123 Open error on record fileCause: Internal errorRemedy: Restart software or reinstall when necessary,report to EMCO, if repeatable.8124 Write error on record fileCause: Internal errorRemedy: Restart software or reinstall when necessary,report to EMCO, if repeatable.8125 Invalid memory for record bufferCause: Insufficient RAM, record time exceeding.Remedy: Restart software, ev. remove drivers etc. togain more RAM, reduce record time.8126 AC Interpolation overrunCause: Ev. insufficient computer performance.Remedy: Set a longer interrupt time in WinConfig.This may result in poorer path accuracy.8127 Insufficient memoryCause: Insufficient RAMRemedy: Close other programs, restart software,ev. remove drivers etc. to gain more RAM.8128 Invalid message to ACCause: Internal errorRemedy: Restart software or reinstall when necessary,report to EMCO, if repeatable.8129 Invalid MSD data - axisconfig.see 8128.8130 Internal init error ACsee 8128.8130 Internal init error ACsee 8128.8132 Axis accessed by multiple channelssee 8128.8133 Insufficient NC block memory ACsee 8128.8134 Too much center points programmedsee 8128.8135 No centerpoint programmedsee 8128.8136 Circle radius too smallsee 8128.H 6
EMCO WINNC SINUMERIK 810/820 TALARMS / MESSAGES8137 Invalid for Helix specifiedCause: Wrong axis for helix. The combination oflinear and circular axes does not match.Remedy: Program correction.8140 Maschine (ACIF) not respondingCause: Machine off or not connected.Remedy: Switch on machine or connect.8141 Internal PC-COM errorCause: Internal errorRemedy: Restart software or reinstall when necessary,report to EMCO, if repeatable.8142 ACIF Program errorCause: Internal errorRemedy: Restart software or reinstall when necessary,report to EMCO, if repeatable.8143 ACIF packet acknowledge missingsee 8142.8144 ACIF startup errorsee 8142.8145 Fatal init data error (acif.hex)see 8142.8146 Multiple request for axissee 8142.8147 Invalid PC-COM state (DPRAM)see 8142.8148 Invalid PC-COM command (CNo)see 8142.8149 Invalid PC-COM command (Len)see 8142.8150 Fatal ACIF errorsee 8142.8151 AC Init Error (missing RPG file)see 8142.8152 AC Init Error (RPG file format)see 8142.8153 FPGA program timeout on ACIFsee 8142.8154 Invalid Command to PC-COMsee 8142.8155 Invalid FPGA packet acknowledgesee 8142 or hardware error on ACIF board (contactEMCO Service).8156 Sync within 1.5 revol. not foundsee 8142 or Bero hardware error (contact EMCOService).8157 Data record donesee 8142.8158 Bero width too large (referencing)see 8142 or Bero hardware error (contact EMCOService).8159 Function not implementedBedeutung: In normal operation this function can notbe executed8160 Axis synchronization lost axis 3..7Cause: Axis spins or slide is locked, axis synchronisationwas lostRemedy: Approach reference point8164 Software limit switch max axis 3..7Cause: Axis is at traverse area endRemedy: Retract axis8168 Software limit overtravel axis 3..7Cause: Axis is at traverse area endRemedy: Retract axis8172 Communication error to machineCause: Internal errorRemedy: Restart software or reinstall when necessary,report to EMCO, if repeatable.Check connection PC - machine, eventuallyeliminate distortion sources.8173 INC while NC program is running8174 INC not allowed8175 MSD file could not be openedCause: Internal errorRemedy: Restart software oder bei Bedarf neu installieren,report to EMCO, if repeatable.8176 PLS file could not be openedsee 8175.8177 PLS file could not be accessedsee 8175.8178 PLS file could not be writtensee 8175.8179 ACS file could not be openedsee 8175.8180 ACS file could not be accessedsee 8175.8181 ACS file could not be writtensee 8175.8182 Gear change not allowed8183 Gear too high8184 Invalid interpolaton command8185 Forbidden MSD data changesee 8175.8186 MSD file could not be openedsee 8175.H 7
Page 2 and 3:
EMCO WINNC SINUMERIK 810/820 TPREFA
Page 4 and 5:
EMCO WINNC SINUMERIK 810/820 TCONTE
Page 6 and 7:
EMCO WINNC SINUMERIK 810/820 TKEY D
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
EMCO WINNC SINUMERIK 810/820 TBASIC
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
EMCO WINNC SINUMERIK 810/820 TOPERA
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32: EMCO WINNC SINUMERIK 810/820 TOPERA
Page 33 and 34: EMCO WINNC SINUMERIK 810/820 TPROGR
Page 65 and 66: EMCO WINNC SINUMERIK 810/820 T@-COD
Page 67 and 68: EMCO WINNC SINUMERIK 810/820 T@-COD
Page 69 and 70: EMCO WINNC SINUMERIK 810/820 TSURVE
Page 77 and 78: EMCO WINNC SINUMERIK 810/820 TALARM
Page 81: EMCO WINNC SINUMERIK 810/820 TALARM
show all

EMCO WinNC SINUMERIK 810/820 T Software Description ...

Create successful ePaper yourself

Delete template?

Save as template?