EMCO WinNC SINUMERIK 810/820 T Software Description ...

More documents

Recommendations

Info

EMCO WINNC SINUMERIK 810/820 TALARMS / MESSAGES2520 ORDxx RS485 device absentCause: With program start not all necessary RS485participant were present or while programrun a participant failed.(AC) Axis controller(SPS) PLC(MT) Control keyboardRemedy: switch on RS485 participant (machine,control keyboard), check cables andconnectors, check terminator plug, reportto EMCO if repeatable2521 ORDxx RS485 communication errorRemedy: switch off / on the PC, report to EMCO ifrepeatable2522 ORDxx RS485 communication errorCause: internal errorRemedy: switch on/off PC, report to EMCO ifrepeatable2523 ORDxx INIT error on RS485 PC-boardsee "Installation of the Software, Mistakes with Installationof the Software"2524 ORDxx Gen.-Failure RS485 PC-boardRemedy: switch off/on PC, report to EMCO ifrepeatable2525 ORDxx Transmit error RS485Remedy: check RS485 cables and connectors, checkterminator plug, check for externalelectromagnetic interferences2526 ORDxx Transmit error RS485see 25252527 ORDxx Internal error ACRemedy: switch off/on machine, report to EMCO ifrepeatable2528 ORDxx Operating system error PLCRemedy: switch off/on machine, report to EMCO ifrepeatable2529 ORDxx External keyboard errorRemedy: The control keyboard must be switched onafter the PC when it is connected to RS232,switch off/on external keyboard, report toEMCO if repeatable2540 ORDxx Error on storing setting-dataCause: hard disk full, wrong path determined, missingwrite accessRemedy: check hard disk, if repeatable reinstallsoftware2545 ORDxx Drive / Device not readyRemedy: insert disk, close drive2546 ORDxx Checksum error machine-dataRemedy: report to EMCO if repeatable2550 ORDxx PLC simulation errorRemedy: report to EMCO if repeatable2551 ORDxx PLC simulation errorRemedy: report to EMCO if repeatable2562 Read error on CNC programCause: error of program file, disk or hard disk errorRemedy: solve problem on DOS level, eventuallyreinstall software2614 Nxxxx Internal error MSDRemedy: report to EMCO if repeatable2650 Nxxxx Wrong Cycle-CallCause: invalid cycle call, if cycle will be called withG codeRemedy: report to EMCO if repeatable2849 Nxxxx Internal error CRCRemedy: report to EMCO if repeatable2904 Nxxxx Helix Z path too largeThe angle between the helix and the tangent to thearc must be less than 45°.Remedy: correct program3000 Nxxxx General Program errorCause: no circle parameter programmed, wrongplane for circle (G17/18/19), chamfer/radius/thread pitch already programmed,thread pitch missing, ...Remedy: correct program3001 Nxxxx More than 5 geomety parameterCause: wrong parameter for contour draftRemedy: correct program3002 Nxxxx Polar/radius errorCause: No centre point specified, centre point inwrong plane (G17/18/19)Remedy: correct program3003 Nxxxx Invalid addressThe entered address is not allowed.Remedy: correct program3004 Nxxxx CL800 ErrorCause: general cycle error with cycle language CL-800, wrong parameter, invalid value,incorrect contour program, M17 in contourprogram missingRemedy: correct program3005 Nxxxx Contour definition errorCause: no valid contour draft with the programmedcoordinates, invalid parameter, invalidvaluesRemedy: correct programH 4
EMCO WINNC SINUMERIK 810/820 TALARMS / MESSAGES3006 Nxxxx Wrong block structureCause: too much M/H/T/D/S/G commands in oneblock, G commands of the same grouptwice programmed in block, circle with morethan 2 axes or polar coordinate centrepoint with more than 2 axes, scale factorprogrammed twice in a block, change ofplane / zero offset / tool change / mirrorwhile contour draft, no valid contour draftwith the programmed addressesRemedy: correct program3008 Nxxxx Subroutine errorCause: subroutine counter invalidsubroutine end with M30nesting depth overrideRemedy: correct subroutine counterprogram M17, max. 4 subroutines nested3011 Nxxxx To many axes/axis twiceCause: the position (axis) was already programmed,too much axes with block with thread/mirrorRemedy: correct program3012 Nxxxx Block not in memoryCause: program end without M30, jump target notfoundRemedy: correct program3021 Nxxxx CRC contour errorCause: The tool radius is too large in relation to thesmallest contour element, contour violationwith full circle, programmed arc radiussmaller than the tool radiusRemedy: correct program3042 Wrong pictureRemedy: switch off / on the PC, reprot to EMCO ifrepeatable3049 Wrong simulation areaCause: With graphik simulation no or an invalidsimulation area was put inRemedy: put in/correct simulation area3081 Nxxxx CRC not selected for approachingCause: With soft approaching / leaving a contourG41 or G42 must be activeRemedy: correct program4100 Nxxxx No D-number activeCause: cycle alarm: no tooloffset activeRemedy: activate tool correction (D)4101 Nxxxx Cutter radius = 0Remedy: enter cutter radius4102 Nxxxx Cutter radius too largeRemedy: correct cutter radius4103 Nxxxx Tool to wideRemedy: L93: use other tool4120 Nxxxx Spindle rotat. dir. n. progr.Remedy: L94: program spindle direction4121 Nxxxx Spindle not in tol. range4122 Nxxxx Calculated feed too largeRemedy: L841: reduce feed4140 Nxxxx Fin. part diam. too smallRemedy: alter program4180 Nxxxx Option not available !Remedy: order option (L841, L94)4200 Nxxxx Check definition of RRemedy: correct R326000 - 7999 Machine alarmssee "Machine Alarms"8004 ORDxx Failure main-drive unit8005 - 8009 ORDxx Internal error ACRemedy: report to EMCO if repeatable8010 ORDxx Syncr. error main driveCause: synchronisation mark missing for main driveRemedy: report to service technician, if repeatable8011 - 8013 ORDxx Internal error ACRemedy: report to EMCO, if repeatable8014 ORDxx Decel.-time of axis too highRemedy: report to service technician, if repeatable8018 ORDxx Internal error ACRemedy: report to EMCO, if repeatable8021 ORDxx Internal error ACRemedy: report to EMCO, if repeatable8022 ORDxx Internal error ACRemedy: report to EMCO, if repeatable8023 ORDxx Invalid Z value for helixCause: The Z value of the helix must be smallerthan the length of the arc to be traversedRemedy: Program correction8100 Fatal init error ACCause: Internal errorRemedy: Restart software or reinstall when necessary,report to EMCO, if repeatable.8101 Fatal init error ACsee 8101.8102 Fatal init error ACsee 8101.8103 Fatal init error ACsee 8101.H 5
Page 2 and 3:
EMCO WINNC SINUMERIK 810/820 TPREFA
Page 4 and 5:
EMCO WINNC SINUMERIK 810/820 TCONTE
Page 6 and 7:
EMCO WINNC SINUMERIK 810/820 TKEY D
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
EMCO WINNC SINUMERIK 810/820 TBASIC
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
EMCO WINNC SINUMERIK 810/820 TOPERA
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30: EMCO WINNC SINUMERIK 810/820 TOPERA
Page 31 and 32: EMCO WINNC SINUMERIK 810/820 TOPERA
Page 33 and 34: EMCO WINNC SINUMERIK 810/820 TPROGR
Page 65 and 66: EMCO WINNC SINUMERIK 810/820 T@-COD
Page 67 and 68: EMCO WINNC SINUMERIK 810/820 T@-COD
Page 69 and 70: EMCO WINNC SINUMERIK 810/820 TSURVE
Page 77 and 78: EMCO WINNC SINUMERIK 810/820 TALARM
Page 79: EMCO WINNC SINUMERIK 810/820 TALARM
show all

EMCO WinNC SINUMERIK 810/820 T Software Description ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?