EMCO WinNC SINUMERIK 810/820 T Software Description ...

More documents

Recommendations

Info

EMCO WINNC SINUMERIK 810/820 T@-CODES@- Befehl@448 @4e1 = + = - = x = / FunktionProgrammierter Interpolationsparameter für Kreis und GewindeWert 3: Achs-Nr. 1, 2, ...Spindel-Beschleunigungskonstante schreibenWert 1: Spindel-Nr. 0 bis 6Wert 2: Getriebestufe 1 bis 8Wert 3: Spindelbeschleunigungszeitkonstante 0 bis 16000AdditionSubtraktionMultiplikationDivision@610 Betragsbildung@613 Quadratwurzel@614 Wurzel aus Quadratsumme@620 Inkrementiern von mit 1@621 Dekrementiern von mit 1@622 Ganzzahliger Anteil@630 Sinus@631 Cosinus@632 Tangens@634 Arcus Sinus@637 Winkel aus zwei Vektorkomponenten@640 nat. Logarithmus@641 e ExponentialfunktionReferenzaufbereitung@710 Var 1: Ausg.daten ab Var 1Var 2: Eing.datum ab Var 2SchnittpunktberechnungVar 1: Ausg.daten ab Var 1@711 Var 2: Erste Kontur ab Var 2Var 3: mit 0 vorbesetzenStartvorbereitung für Zyklen@713 Var: Ausgangsdaten ab Var@714 Stop der Decodierung, bis Zwischenspeicher leer istE 4
EMCO WINNC SINUMERIK 810/820 TSURVEY PAGESG: Survey PagesSurvey Softkey ExplanationsACTUAL BLOCK(Current block)The current block is the block currently beingprocessed. The display shows: The block before thecurrent block, the current block and the block afterthe current block.ADD. FUNCTION(Additional function)The additional functions (5th M Group) fixed by themachine tool manufacturer are grouped together inthis function. Preselect: softkey „GUIDING“AREA W-PIECE(Work piece area)You enter the simulation area, and the workpiecedimensions.AXIALYou enter the setting data for the axes.BLOCK ENDYou select the character for „Block End (LF)“ viasoftkey.Preselect: „GUIDING“ softkey.BLOCK NUMBERThe block number is automatically generated by thecontrol in steps of five.BLOCK SEARCHBlock search makes it possible to start the operationat any point in the program. During block search, thesame calculations are carried out as in normal programoperation, however there is no axis movement.BTR STARTnot activeCIRCLEYou select the G functions for circular interpolationwith this softkey.Preselect: „GUIDING“ softkey (operator prompting).CONTOURThis function simplifies programming of workpiececontours with the transfer of values directly from thedrawing and graphic displays.You can select the following elements and combinations:• Line• Line - circle• Circle• Circle - line• Circle - circle• 2 - point definition• 2 - angle definitionCOPYYou copy a part program and re-enter it into memoryunder another program number.CORR. BLOCK(Correction block)An error in the program is marked with the cursor(correction pointer).CURRENT PRG PTR(current program pointer)The display shows the subroutine nesting with numberof runs and actual block number of the subroutine.CURRENT VALUESThe display shows the values valid for the currentoperating sequence.CYCLESThe following are displayed:• The stored cycle numbers• The number of characters used• The free memory spaceCycles are protected subroutines which can be calledfor frequently used technologies or for machinespecificoperations (stock removal cycles, drillingcycles, tool change cycles).The values required are defined as parameter assignmentsbefore the cycles are called (cycle parameterassignment).G 1
Page 2 and 3:
EMCO WINNC SINUMERIK 810/820 TPREFA
Page 4 and 5:
EMCO WINNC SINUMERIK 810/820 TCONTE
Page 6 and 7:
EMCO WINNC SINUMERIK 810/820 TKEY D
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
EMCO WINNC SINUMERIK 810/820 TBASIC
Page 15 and 16:
EMCO WINNC SINUMERIK 810/820 TBASIC
Page 17 and 18: EMCO WINNC SINUMERIK 810/820 TBASIC
Page 19 and 20: EMCO WINNC SINUMERIK 810/820 TBASIC
Page 21 and 22: EMCO WINNC SINUMERIK 810/820 TOPERA
Page 33 and 34: EMCO WINNC SINUMERIK 810/820 TPROGR
Page 65 and 66: EMCO WINNC SINUMERIK 810/820 T@-COD
Page 67: EMCO WINNC SINUMERIK 810/820 T@-COD
Page 71 and 72: EMCO WINNC SINUMERIK 810/820 TSURVE
Page 77 and 78: EMCO WINNC SINUMERIK 810/820 TALARM
show all

EMCO WinNC SINUMERIK 810/820 T Software Description ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?