EMCO WinNC SINUMERIK 810/820 T Software Description ...

More documents

Recommendations

Info

EMCO WINNC SINUMERIK 810/820 TBASICSTool Data Measuring1/7\SH/1/ 7\SHDirection of the length correction for the tool typesAim of the tool data measuring:The CNC should use the tool tip for positioning, notthe tool mount reference point.Every tool which is used for machining has to bemeasured. The distances in both axis directionsbetween tool mount reference point and tool tip are tobe measured.In the so-called tool register the measured lengthcorrections, the cutter radius and the cutter positioncan be stored.Every tool offset number D1 - D99 is related to a tool.The correction number can be any register number,but has to be considered with tool call in program.ExampleThe length corrections of a tool in the tool turretstation 4 have been stored as correction number 41.Tool call in program: T4 D41The address T marks the position in the tool turret,the address D marks the correction number belongingto the tool.The length corrections can be measured halfautomatically,cutter radius and cutter position haveto be inserted manually.The cutter position must always be inserted!Inserting the cutter radius is only necessary for usingthe cutter radius compensation with this tool.5Tool radius RThe tool data measuring occurs for type 1-9:L1: in -X direction absolute from point "N"in radiusL2: in -Z direction absolute from point "N"R :cutter radiusType: cutter position (1-9)The tool data measuring occurs for type 10:L1: in -Z direction absolute from point "N"Type: drilling tool (10)B 4
EMCO WINNC SINUMERIK 810/820 TBASICSCutter position (Type)Cutter positionLook at the tool like it is clamped at the machine todetermine the tool type.For machines with the tool below (in front of) theturning centre (e.g. PC TURN 50/55) the values inbrackets must be used because of the opposite +Xdirection of these machines.With "wear" occurs the correction of not exactmeasured tool data or worn tools after severalmachining runs. The inserted length corrections willbe added to or subtracted from the geometry of thetool incrementally.X+/- .....incremental in diameterZ+/- ......incrementalR+/- .....incrementalB 5
Page 2 and 3: EMCO WINNC SINUMERIK 810/820 TPREFA
Page 4 and 5: EMCO WINNC SINUMERIK 810/820 TCONTE
Page 6 and 7: EMCO WINNC SINUMERIK 810/820 TKEY D
Page 13 and 14: EMCO WINNC SINUMERIK 810/820 TBASIC
Page 15: EMCO WINNC SINUMERIK 810/820 TBASIC
Page 19 and 20: EMCO WINNC SINUMERIK 810/820 TBASIC
Page 21 and 22: EMCO WINNC SINUMERIK 810/820 TOPERA
Page 33 and 34: EMCO WINNC SINUMERIK 810/820 TPROGR
Page 65 and 66: EMCO WINNC SINUMERIK 810/820 T@-COD
Page 67 and 68:
EMCO WINNC SINUMERIK 810/820 T@-COD
Page 69 and 70:
EMCO WINNC SINUMERIK 810/820 TSURVE
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
EMCO WINNC SINUMERIK 810/820 TALARM
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
show all

EMCO WinNC SINUMERIK 810/820 T Software Description ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?