EMCO WinNC SINUMERIK 810/820 T Software Description ...

More documents

Recommendations

Info

EMCO WINNC SINUMERIK 810/820 TPREFACEPrefaceThe software EMCO WinNC SINUMERIK 810/820 T Turning is a part of theEMCO education concept on PC basis.Target of this concept is learning to operate and program the original control atthe PC.The turning machines of the EMCO PC TURN und CONCEPT TURN series canbe directly controlled via PC by means of the EMCO WinNC for the EMCOTURN.The operation is rendered very easy by the use of a digitizer or the controlkeyboard with TFT flat panel display (optional accessory), and it is didacticallyespecially valuable since it remains very close to the original control.This manual does not include the whole functionality of the control softwareSINUMERIK 810/820 T Turning, however emphasis was laid on the simple andclear illustration of the most important functions so as to achieve a mostcomprehensive learning success.In case any questions or proposals for improving this manual should arise,please contact us directly:EMCO MAIER Gesellschaft m. b. H.Department Technical DocumentationA-5400 Hallein, AustriaAll rights reserved, reproduction only by authorization of Messrs. EMCO MAIER© EMCO MAIER Gesellschaft m.b.H., Hallein 20032
EMCO WINNC SINUMERIK 810/820 TCONTENTSContentsA: Key DescriptionControl Keyboard, Digitizer Overlay .....................................A1Key functions .....................................................................A2Address and Numeric Keyboard .........................................A2Machine Control Keys ........................................................A4PC Keyboard .....................................................................A6Screen with Softkeys ..........................................................A7B: BasicsReference Points of the EMCO Lathes ................................B1Zero Offset ........................................................................B2Coordinate System.............................................................B2Coordinate System with Absolute Programming .............B2Coordinate System with Incremental Programming ........B2Input of the ........................................................................B3Zero Offset ........................................................................B3Tool Data Measuring ..........................................................B4Input of the Tool Data .........................................................B6Tool Data Measuring by Scraping ........................................B7Tool Data Measuring with the Optical Presetting Device .......B8C: Operating SequencesSurvey Modes ................................................................... C1Approach the Reference Point ........................................... C2Input of the Gear Position .................................................. C2Setting of Language and Workpiece directory ..................... C2Input of Programs ............................................................. C3Call up an existing or new program .............................. C3Input of a block ........................................................... C3Insert Block ................................................................. C3Delete Block ............................................................... C3Insert Word ................................................................. C3Alter Word .................................................................. C3Delete Word................................................................ C3Program Input with Guiding Function ............................ C4Program Input with CAD/CAM Systems ........................ C4Program Administration ..................................................... C5Copy Program............................................................. C5Rename Program........................................................ C5Delete Program........................................................... C5Data Input-Output ............................................................. C5Data Input via COM1 / COM2 ...................................... C6Data Import ................................................................. C6Data Output ................................................................ C7Print Data ................................................................... C7Adjusting the Serial Interface ....................................... C8Program Run .................................................................... C9Start of a Part Program ................................................ C9Messages while program run ....................................... C9Program Influence ....................................................... C9Overstore ..................................................................C10Block Search .............................................................C10Program Interruption ..................................................C10Status Display of the PLC ...........................................C10Display of the Software Versions .................................C10Graphic simulation ........................................................... C11D: ProgrammingProgram Structure ............................................................. D1Addresses ........................................................................ D1Survey of G Commands .................................................... D2Survey of M Commands .................................................... D2Survey of Cycles ............................................................... D2Description of G Commands .............................................. D3G00 Positioning (Rapid Traverse) ...................................... D3G01 Linear Interpolation .................................................... D3G02 Circular Interpolation Clockwise .................................. D4G03 Circular Interpolation Counterclockwise ....................... D4G04 Dwell ......................................................................... D5G09 Exact Stop ................................................................. D5G10 - G13 Polar Coordinate Interpolation ........................... D5G25/G26 Programmable working area limitation ................. D6G16, G18 Working plane selection ..................................... D6G33 Thread Cutting ........................................................... D7Cutter Radius Compensation ............................................. D7G40 Cancel Cutter Radius Compensation .......................... D9G41 Cutter Radius Compensation Left ............................... D9G42 Cutter Radius Compensation Right ............................. D9G48 Leave as Approached .............................................. D10G50 Cancel Scale Modification ........................................ D10G51 Scale Modification .................................................... D10G53 Cancel Zero Offset Blockwise ....................................D11G54 - G57 Zero Offset 1 - 4 ..............................................D11G58/G59 Programmable Zero Offsets ...............................D11G60 Exact Stop Mode...................................................... D12G62, G64 Deselection Exact Stop Mode ........................... D12G63 Thread tapping with compenstion chuck .................... D12G70 Measuring in Inches ................................................. D13G71 Measuring in Millimetre ............................................ D13G90 Absolute Programming ............................................. D14G91 Incremental Programming ........................................ D14G92 Spindle Speed Limit ................................................. D14G 92 Cylindrical interpolation ........................................... D15G94 Feed per Minute ...................................................... D17G95 Feed per Revolution................................................. D17G96 Constant Cutting Speed ........................................... D17G97 Constant Spindle Speed ........................................... D17G131 Transmit ................................................................ D18G147 Soft Approach to Contour with Linear ...................... D19G247 Soft Approach to Contour with Quarter Circle ........... D19G347 Soft Approach to Contour with Semicircle ................ D19G148 Soft Leaving with Linear ......................................... D19G248 Soft Leaving with Quarter Circle .............................. D19G348 Soft Leaving with Semicircle ................................... D19Description of M Commands ............................................ D21M00 Programmed Stop Unconditional .............................. D21M01 Programmed Stop Conditional .................................. D21M02 Main Program End ................................................... D21M03 Main Spindle ON Clockwise...................................... D21M04 Main Spindle ON Counterclockwise .......................... D21M05 Main Spindle Off ...................................................... D21M08 Coolant ON ............................................................. D22M09 Coolant OFF ........................................................... D22M17 Subroutine End ....................................................... D22M20 Tailstock BACK ........................................................ D22M21 Tailstock FORWARD ................................................ D22M25 Open Clamping Device ............................................ D22M26 Close Clamping Device............................................ D22M30 Main Program End ................................................... D22M52 C- Axis ON .............................................................. D22M53 C- Axis OFF ............................................................ D22M71 Puff Blowing ON ...................................................... D22M72 Puff Blowing OFF..................................................... D223
Page 4 and 5: EMCO WINNC SINUMERIK 810/820 TCONTE
Page 6 and 7: EMCO WINNC SINUMERIK 810/820 TKEY D
Page 13 and 14: EMCO WINNC SINUMERIK 810/820 TBASIC
Page 21 and 22: EMCO WINNC SINUMERIK 810/820 TOPERA
Page 33 and 34: EMCO WINNC SINUMERIK 810/820 TPROGR
Page 53 and 54:
EMCO WINNC SINUMERIK 810/820 TPROGR
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
EMCO WINNC SINUMERIK 810/820 T@-COD
Page 67 and 68:
EMCO WINNC SINUMERIK 810/820 T@-COD
Page 69 and 70:
EMCO WINNC SINUMERIK 810/820 TSURVE
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
EMCO WINNC SINUMERIK 810/820 TALARM
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
show all

EMCO WinNC SINUMERIK 810/820 T Software Description ...

Create successful ePaper yourself

Delete template?

Save as template?