SIM300D AT Command Set - Distributed Systems and Networking

More documents

Recommendations

Info

SIM300D AT Command Set Confidential SIMCOM Reference GSM07.07 Parameter 0 buffer unsolicited result codes in the MT; if MT result SIM300D_AT_V1.00 Page 106 of 180 code buffer is full, the oldest ones can be discarded. No codes are forwarded to the TE. 1 discard unsolicited result codes when MT-TE link is reserved (e.g. in on-line data mode); otherwise forward them directly to the TE Unsolicited Result Codes supported: +CGEV: NW DEACT , [,] +CGEV: ME DEACT , [,] +CGEV: NW DETACH +CGEV: ME CLASS parameter Packet Data Protocol type (see +CGDCONT command) Packet Data Protocol address (see +CGDCONT command) Context Id (see +CGDCONT command) GPRS mobile class (see +CGCLASS command) Note 5.2.10 AT+CGREG Network registration status AT+CGREG Network registration status Test command +CGREG=? Read command +CGREG? Set command +CGREG=[] Response +CGREG: (list of supported s) Parameter See set command Response +CGREG:,[,,] +CME ERROR: Parameter See set command Response OK ERROR Parameter 0 disable network registration unsolicited result code 1 enable network registration unsolicited result code +CGREG: 2 enable network registration and location information unsolicited result code +CGREG: [,,] 0 not registered, ME is not currently searching a new operator to register to
SIM300D AT Command Set Confidential SIMCOM Reference GSM07.07 1 registered string type; two byte location area code in hexadecimal format (e.g. “00C3” equals 195 in decimal) string type; two bytes cell ID in hexadecimal format Note For parameter stat, options 0 and 1 supported only. 5.2.11 AT+CGSMS Select service for MO SMS messages AT+CGSMS Select service for MO SMS messages Test command +CGSMS=? Read command +CGSMS? Set command +CGSMS=[] Reference GSM07.07 Response +CGSMS: (list of currently available s) Parameter See set command Response +CGSMS: Parameter See set command Response OK ERROR Parameter a numeric parameter which indicates the service or service Note preference to be used 0 GPRS 1 circuit switched SIM300D_AT_V1.00 Page 107 of 180 2 GPRS preferred (use circuit switched if GPRS not available) 3 circuit switched preferred (use GPRS if circuit switched not available) The circuit switched service route is the default method 5.2.12 AT+CGCOUNT GPRS packet counters AT+CGCOUNT GPRS packet counters Test command +CGCOUNT=? Read command +CGCOUNT? Response +CGCOUNT: (list of supported s),(list of supported s),(list of supported s) Parameter See set command Response +CGCOUNT:,[,] [+CGCOUNT:,[,]
Page 1 and 2:
SIM300D AT Command Set SOFTWARE SPE
Page 3 and 4:
SIM300D AT Command Set Confidential
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56: SIM300D AT Command Set Confidential
Page 105: SIM300D AT Command Set Confidential
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
show all

SIM300D AT Command Set - Distributed Systems and Networking

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?