SIM300D AT Command Set - Distributed Systems and Networking

More documents

Recommendations

Info

SIM300D AT Command Set Confidential SIMCOM Reference Unsolicited result code When the presentation of the CLI at the TE is enabled (and calling subscriber allows), an unsolicited result code is returned after every RING (or +CRING: ) at a mobile terminating call. +CLIP: , , Parameter string type phone number of calling address in format specified by SIM300D_AT_V1.00 Page 50 of 180 type of address octet in integer format; 129 Unknown type(IDSN format number) 128 Unknown type(unknown number format) 161 National number type(IDSN format) 145 International number type(ISDN format ) 177 Network specific number(ISDN format) string type alphanumeric representation of 3.2.21 AT+CLIR Calling Line Identification Restriction AT+CLIR Calling Line Identification Restriction Read Command AT+CLIR? Test Command AT+CLIR=? Write Command AT+CLIR= Response +CLIR: , OK corresponding to the entry found in phone book If error is related to ME functionality: +CME ERROR: Parameters see write command Response +CLIR: (list of supported s) OK Response TA restricts or enables the presentation of the CLI to the called party when originating a call. The command overrides the CLIR subscription (default is restricted or allowed) when temporary mode is provisioned as a default adjustment for all following outgoing calls. This adjustment can be revoked by using the opposite command. OK
SIM300D AT Command Set Confidential SIMCOM Reference If error is related to ME functionality: +CME ERROR: Parameters (parameter sets the adjustment for outgoing calls): SIM300D_AT_V1.00 Page 51 of 180 0 presentation indicator is used according to the subscription of the CLIR service 1 CLIR invocation 2 CLIR suppression (parameter shows the subscriber CLIR service status in the network): 0 CLIR not provisioned 3.2.22 AT+CMEE Report mobile equipment error AT+CMEE Report mobile equipment error Test command AT+CMEE=? Read command AT+CMEE? Set command AT+CMEE= Reference GSM 07.07 [13] Response 1 CLIR provisioned in permanent mode 2 unknown (e.g. no network, etc.) 3 CLIR temporary mode presentation restricted 4 CLIR temporary mode presentation allowed +CMEE: (list of supported s) OK Parameters see set command Response +CMEE: OK Parameters see set command Response TA disables or enables the use of result code +CME ERROR: as an indication of an error relating to the functionality of the ME. OK Parameters 0 disable result code 1 enable result code and use numeric values 2 enable result code and use verbose values
Page 1 and 2: SIM300D AT Command Set SOFTWARE SPE
Page 3 and 4: SIM300D AT Command Set Confidential
Page 49: SIM300D AT Command Set Confidential
Page 101 and 102:
SIM300D AT Command Set Confidential
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
show all

SIM300D AT Command Set - Distributed Systems and Networking

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?