SIM300D AT Command Set - Distributed Systems and Networking

More documents

Recommendations

Info

SIM300D AT Command Set Confidential SIMCOM 3.2.23 AT+COLP Connected Line Identification Presentation AT+COLP Connected Line Identification Presentation Read Command AT+COLP? Test Command AT+COLP=? Write Command AT+COLP=[ ] Response +COLP: , OK If error is related to ME functionality: +CME ERROR: Parameters See write command Response +COLP: (list of supported s) OK Parameters See write command Response TA enables or disables the presentation of the COL (Connected Line) at the TE for a mobile originated call. It has no effect on the execution of the supplementary service COLR in the network. Intermediate result code is returned from TA to TE before any +CR or V.25ter responses. OK Parameters (parameter sets/shows the result code presentation status in the TA): 0 disable 1 enable (parameter shows the subscriber COLP service status in the Intermediate result code network): 0 COLP not provisioned 1 COLP provisioned 2 unknown (e.g. no network, etc.) When enabled (and called subscriber allows), an intermediate result code is returned before any +CR or V.25ter responses: +COLP:,[,, [,]] SIM300D_AT_V1.00 Page 52 of 180
SIM300D AT Command Set Confidential SIMCOM Reference Parameters 3.2.24 AT+COPS Operator selection AT+COPS Operator selection Test command AT+COPS=? Read command AT+COPS? string type phone number of format specified by SIM300D_AT_V1.00 Page 53 of 180 type of address octet in integer format; 129 Unknown type(IDSN format number) 128 Unknown type(unknown number format) 161 National number type(IDSN format) 145 International number type(ISDN format ) 177 Network specific number(ISDN format) string type sub address of format specified by type of sub address octet in integer format (refer GSM 04.08 [8] sub clause 10.5.4.8) optional string type alphanumeric representation of Response corresponding to the entry found in phone book TA returns a list of quadruplets, each representing an operator present in the network. Any of the formats may be unavailable and should then be an empty field. The list of operators shall be in order: home network, networks referenced in SIM, and other networks. +COPS: list of supported(, long alphanumeric , numeric )s [,,(list of supported s),(list of supported s)] OK If error is related to ME functionality: +CME ERROR: Parameters see set command Response TA returns the current mode and the currently selected operator. If no operator is selected, and are omitted. +COPS: [, [, ]] OK If error is related to ME functionality: +CME ERROR: Parameters see set command
Page 1 and 2: SIM300D AT Command Set SOFTWARE SPE
Page 3 and 4: SIM300D AT Command Set Confidential
Page 51: SIM300D AT Command Set Confidential
Page 103 and 104:
SIM300D AT Command Set Confidential
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
show all

SIM300D AT Command Set - Distributed Systems and Networking

Create successful ePaper yourself

Delete template?

Save as template?