SIM300D AT Command Set - Distributed Systems and Networking

More documents

Recommendations

Info

SIM300D AT Command Set Confidential SIMCOM Reference Parameter 7.2.7 AT+CALARM Set alarm AT+CALARM Set alarm Read Command AT+CALAR M=? Set Command AT+CALAR M= ,,, currentUart 1 use serial line 1 2 use serial line 2(gprs) 3 use serial line 2 4 last commond use serial line 1 5 last commond use serial line 2 Uart 1 use serial line 1 2 use serial line 2(gprs) 3 use serial line 2 Baud ( If uart is 2 or 3) 9600,19200,28800,38400,57600,115200 Response : + CALARM: ,,, ok Parameter: See set command Response : ok Parameter: < state > an integer parameter which indicates whether enable or disable alarm. 0 CLEAR ALARM 1 SET ALARM < time > a string parameter which indicates the time when alarm arrives. SIM300D_AT_V1.00 Page 138 of 180 The format is “yy/MM/dd,hh:mm:ss+-zz” where characters indicate the last two digits of year, month, day, hour, minute, second and time zone. The time zone is expressed in quarters of an hour between the local time and GMT, ranging from -47 to +48. < repeat > an integer parameter which indicates the repeat mode 0 None 1 Daily 2 Weekly 3 Monthly an integer parameter which indicates the method of dealing power
SIM300D AT Command Set Confidential SIMCOM Reference Note: 7.2.8 AT+CADC Read ADC AT+CADC Read ADC Read Command AT+ CADC? Test Command AT+CADC=? when alarm arrives. 0 None Only send “ALARM RING” to serial port 1 Alarm power off SIM300D_AT_V1.00 Page 139 of 180 Send “ALARM RING” to serial port and power off in 5 seconds 2 Alarm power on Send “ALARM MODE” to serial port and enter into alarm mode Note: In alarm mode, protocol stack and SIM protocol is closed, only a few AT command can be executed, and system will be powered down after 90 seconds if neither power key is pressed nor functionality is changed to full functionality. If power key is pressed, system will be powered down right now. Response : + CADC: < status>, OK Parameter: See test command Response : + CADC: list of supported s, list of supported s> OK Parameter: 1 success 0 fail integer 0-2400 Note: 7.2.9 AT+CSNS Single numbering scheme AT+CSNS Single numbering scheme Test command Response : AT+ CSNS =? +CSNS:(list of supported modes) Read command AT+ CSNS? Parameter Response : +CSNS:
Page 1 and 2:
SIM300D AT Command Set SOFTWARE SPE
Page 3 and 4:
SIM300D AT Command Set Confidential
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88: SIM300D AT Command Set Confidential
Page 137: SIM300D AT Command Set Confidential
show all

SIM300D AT Command Set - Distributed Systems and Networking

Create successful ePaper yourself

Delete template?

Save as template?