SIM300D AT Command Set - Distributed Systems and Networking

More documents

Recommendations

Info

SIM300D AT Command Set Confidential SIMCOM Reference V.25ter Parameter string type value (“x“), which should equal to an SIM300D_AT_V1.00 Page 16 of 180 alphanumeric field in at least one phone book entry in the searched memories. str formatted as current TE character set specified by +CSCS. string of GSM modifiers: I Actives CLIR (Disables presentation of own number to called party) i Deactivates CLIR (Enable presentation of own number to called party) G Activates Closed User Group invocation for this call only g Deactivates Closed User Group invocation for this call only only required to set up voice call , return to command state Note � Parameter “I” and “i” only if no *# code is within the dial string � *# codes sent with ATD are treated as voice calls. Therefore, the command must be terminated with a semicolon “;” � See ATX command for setting result code and call monitoring parameters. 2.2.7 ATDL Redial last telephone number used ATDL Redial last telephone number used Execution command ATDL Response This command redials the last voice and data call number used. Note: This command may be aborted generally by receiving an ATH command or a character during execution. The aborting is not possible during some states of connection establishment such as handshaking. If error is related to ME functionality +CME ERROR: If no dial tone and (parameter setting ATX2 or ATX4) NO DIALTONE If busy and (parameter setting ATX3 or ATX4) BUSY If a connection cannot be established NO CARRIER If connection successful and non-voice call.
SIM300D AT Command Set Confidential SIMCOM Reference V.25ter CONNECT TA switches to data mode. Note: output only if ATX parameter setting with the >0 When TA returns to command mode after call release OK If successfully connected and voice call OK Note � See ATX command for setting result code and call monitoring parameters. 2.2.8 ATE Set command echo mode ATE Set command echo mode Set command ATE[] Reference V.25ter Response This setting determines whether or not the TA echoes characters received from TE during command state. OK Parameter 0 Echo mode off Note 2.2.9 ATH Disconnect existing connection ATH Disconnect existing connection Execution command ATH[n] Reference V.25ter Response 1 Echo mode on Disconnect existing call by local TE from command line and terminate call OK Note: OK is issued after circuit 109(DCD) is turned off, if it was previously on. Parameter 0 disconnect from line and terminate call Note SIM300D_AT_V1.00 Page 17 of 180
Page 1 and 2: SIM300D AT Command Set SOFTWARE SPE
Page 3 and 4: SIM300D AT Command Set Confidential
Page 15: SIM300D AT Command Set Confidential
Page 67 and 68:
SIM300D AT Command Set Confidential
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
show all

SIM300D AT Command Set - Distributed Systems and Networking

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?