SIM300D AT Command Set - Distributed Systems and Networking

More documents

Recommendations

Info

SIM300D AT Command Set Confidential SIMCOM 2.2.10 ATI Display product identification information ATI Display product identification information Execution command ATI Reference V.25ter Response TA issues product information text Example: SIMCOM_Ltd SIMCOM_SIM300D Revision: 1008B02SIM300D32_ATMEL OK Parameter Note 2.2.11 ATL Set monitor speaker loudness ATL Set monitor speaker loudness Set command ATL[value] Reference V.25ter Response OK Parameter 0 low speaker volume Note 2.2.12 ATM Set monitor speaker mode ATM Set monitor speaker mode Set command ATM[value] Reference V.25ter 1 low speaker volume 2 medium speaker volume 3 high speaker volume � The two commands ATL and ATM are implemented only for V.25 Response OK Parameter compatibility reasons and have no effect. 0 speaker is always off Note SIM300D_AT_V1.00 Page 18 of 180 1 speaker on until TA inform TE that carrier has been detected 2 speaker is always on when TA is off-hook � The two commands ATL and ATM are implemented only for V.25 compatibility reasons and have no effect.
SIM300D AT Command Set Confidential SIMCOM 2.2.13 +++ Switch from data mode or PPP online mode to command mode Switch from data mode or PPP online mode to command mode Execution command +++ Reference V.25ter Response This command is only available during a CSD call or a GPRS connection. The +++ character sequence causes the TA to cancel the data flow over the AT interface and switch to command mode. This allows you to enter AT command while maintaining the data connection to the remote server or, accordingly, the GPRS connection. OK To prevent the +++ escape sequence from being misinterpreted as data, it should comply to following sequence: 1. No characters entered for T1 time (0.5 seconds) 2. “+++” characters entered with no characters in between 3. No characters entered for T1 timer (0.5 seconds) 4. Switch to command mode, otherwise go to step 1. Parameter Note � To return from command mode back to data or PPP online mode: Enter ATO. 2.2.14 ATO Switch from command mode to data mode ATO Switch from command mode to data mode Execution command ATO[n] Reference V.25ter Response TA resumes the connection and switches back from command mode to data mode. If connection is not successfully resumed NO CARRIER else TA returns to data mode from command mode CONNECT Note: only if parameter setting X>0 Parameter 0 switch from command mode to data mode Note 2.2.15 ATP Select pulse dialing ATP Select pulse dialing Set command ATP Response OK SIM300D_AT_V1.00 Page 19 of 180
Page 1 and 2: SIM300D AT Command Set SOFTWARE SPE
Page 3 and 4: SIM300D AT Command Set Confidential
Page 17: SIM300D AT Command Set Confidential
Page 69 and 70:
SIM300D AT Command Set Confidential
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
show all

SIM300D AT Command Set - Distributed Systems and Networking

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?