SIM300D AT Command Set - Distributed Systems and Networking

More documents

Recommendations

Info

SIM300D AT Command Set Confidential SIMCOM 2.2.21 ATS6 Set pause before blind dialing ATS6 Set pause before blind dialing Read command ATS6? Set command ATS6=[] Reference V.25ter Response OK Response OK Parameter 0-2-255 number of seconds to wait before blind dialing Note � No effect for GSM 2.2.22 ATS7 set number of seconds to wait for connection completion ATS7 Set number of seconds to wait for connection completion Read command ATS7? Set command ATS7=[] Reference V.25ter Response OK Response This parameter setting determines the amount of time to wait for the connection completion in case of answering or originating a call. OK Parameter 0-60-255 number of seconds to wait for connection completion Note � If called party has specified a high value for ATS0=, call setup may fail. � The correlation between ATS7 and ATS0 is important Example: Call may fail if ATS7=30 and ATS0=20. � ATS7 is only applicable to data call. 2.2.23 ATS8 set number of second to wait for comma dial modifier ATS8 Set number of second to wait for comma dial modifier Read command ATS8? Set command ATS8=[] Reference V.25ter Response OK Response OK Parameter 0 no pause when comma encountered in dial string Note � No effect for GSM 1-255 number of seconds to wait SIM300D_AT_V1.00 Page 22 of 180
SIM300D AT Command Set Confidential SIMCOM 2.2.24 ATS10 Set disconnect delay after indicating the absence of data carries ATS10 Set disconnect delay after indicating the absence of data carrier Read command ATS10? Set command ATS10=[] Reference V.25ter Response OK Response This parameter setting determines the amount of time that the TA will remain connected in absence of data carrier. If the data carrier is once more detected before disconnect, the TA remains connected. OK Parameter 1-15-255 number of tenths seconds of delay Note 2.2.25 ATT Select tone dialing ATT Select tone dialing Set command ATT Reference V.25ter Response OK Parameter Note � No effect in GSM 2.2.26 ATV Set result code format mode ATV Set result code format mode Set command ATV[] Reference V.25ter Response This parameter setting determines the contents of the header and trailer transmitted with result codes and information responses. When =0 0 OK Parameter When =1 0 Information response: Note SIM300D_AT_V1.00 Page 23 of 180 Short result code format: 1 Information response: Long result code format:
Page 1 and 2: SIM300D AT Command Set SOFTWARE SPE
Page 3 and 4: SIM300D AT Command Set Confidential
Page 21: SIM300D AT Command Set Confidential
Page 73 and 74:
SIM300D AT Command Set Confidential
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
show all

SIM300D AT Command Set - Distributed Systems and Networking

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?