SIM300D AT Command Set - Distributed Systems and Networking

More documents

Recommendations

Info

SIM300D AT Command Set Confidential SIMCOM 2.2.27 ATX Set CONNECT result code ATX Set CONNECT result code Set command ATX[] Reference V.25ter Response This parameter setting determines whether or not the TA detected the presence of dial tone and busy signal and whether or not TA transmits particular result codes OK Parameter 0 CONNECT result code only returned, dial tone and Note SIM300D_AT_V1.00 Page 24 of 180 busy detection are both disabled 1 CONNECT result code only returned, dial tone and busy detection are both disabled 2 CONNECT result code returned, dial tone detection is enabled, busy detection is disabled 3 CONNECT result code returned, dial tone detection is disabled, busy detection is enabled 4 CONNECT result code returned, dial tone and busy detection are both enabled 2.2.28 ATZ set all current parameters to user defined profile ATZ Set all current parameters to user defined profile Set command ATZ[] Reference V.25ter Response TA sets all current parameters to the user defined profile. OK Parameter 0 Reset to profile number 0 Note � The user defined profile is stored in non volatile memory; � If the user profile is not valid, it will default to the factory default profile; � Any additional commands on the same command line are ignored. 2.2.29 AT&C Set circuit Data Carrier Detect (DCD) function mode AT&C Set circuit Data Carrier Detect (DCD) function mode Set command AT&C[] Response This parameter determines how the state of circuit 109(DCD) relates to the detection of received line signal from the distant end. OK Parameter 0 DCD line is always ON 1 DCD line is ON only in the presence of data carrier
SIM300D AT Command Set Confidential SIMCOM Reference V.25ter Note 2.2.30 AT&D Set circuit Data Terminal Ready (DTR) function mode AT&D Set circuit Data Terminal Ready (DTR) function mode Set command AT&D[] Reference V.25ter Response This parameter determines how the TA responds when circuit 108/2(DTR) is changed from the ON to the OFF condition during data mode. OK Parameter 0 TA ignores status on DTR Note SIM300D_AT_V1.00 Page 25 of 180 1 ON->OFF on DTR: Change to command mode with remaining the connected call 2 ON->OFF on DTR: Disconnect call, change to command mode. During state DTR = OFF is auto-answer off. 2.2.31 AT&F Set all current parameters to manufacturer defaults AT&F Set all current parameters to manufacturer defaults Execution command AT&F[] Reference V.25ter Response TA sets all current parameters to the manufacturer defined profile. OK Parameter 0 set all TA parameters to manufacturer defaults. Note 2.2.32 AT&V Display current configuration AT&V Display current configuration Execution command AT&V[] Reference V.25ter Response TA returns the current parameter setting. OK Parameter 0 profile number Note
Page 1 and 2: SIM300D AT Command Set SOFTWARE SPE
Page 3 and 4: SIM300D AT Command Set Confidential
Page 23: SIM300D AT Command Set Confidential
Page 75 and 76:
SIM300D AT Command Set Confidential
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
show all

SIM300D AT Command Set - Distributed Systems and Networking

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?