SIM300D AT Command Set - Distributed Systems and Networking

More documents

Recommendations

Info

SIM300D AT Command Set Confidential SIMCOM Execution command AT+CPWD = , [], Reference GSM 07.07 [13] Response TA sets a new password for the facility lock function. OK Parameter SIM300D_AT_V1.00 Page 60 of 180 "SC" SIM (lock SIM card) (SIM asks password in ME power-up and when this lock command issued) "AO" BAOC (Barr All Outgoing Calls) (refer GSM02.88[6] clause 1) "OI" BOIC (Barr Outgoing International Calls) (refer GSM02.88[6] clause 1) "OX" BOIC-exHC (Barr Outgoing International Calls except to Home Country) (refer GSM02.88[6] clause 1) "AI" BAIC (Barr All Incoming Calls) (refer GSM02.88[6] clause 2) "IR" BIC-Roam (Barr Incoming Calls when Roaming outside the home country) (refer GSM02.88 [6] clause 2) "AB" All Barring services (refer GSM02.30[19]) (applicable only for =0) "AG" All outgoing barring services (refer GSM02.30[19]) (applicable only for =0) "AC" All incoming barring services (refer GSM02.30[19]) (applicable only for =0) "P2" SIM PIN2 password specified for the facility from the user interface or with command. If an old password has not yet been set, is not to enter. new password Note 3.2.32 AT+CR Service Reporting Control AT+CR Service Reporting Control Test command AT+CR=? Read command AT+CR? Response +CR: list of supported s OK Parameters see set command Response +CR: OK
SIM300D AT Command Set Confidential SIMCOM Set command AT+CR= Reference GSM 07.07 [13] Parameters see set command Response TA controls whether or not intermediate result code +CR: is returned from the TA to the TE at a call set up. OK Parameters 0 disable 1 enable Intermediate result code If enabled, an intermediate result code is transmitted at the point during connect negotiation at which the TA has determined which speed and quality of service will be used, before any error control or data compression reports are transmitted, and before any final result code (e.g. CONNECT) is transmitted. +CR: Parameters ASYNC asynchronous transparent SIM300D_AT_V1.00 Page 61 of 180 SYNC synchronous transparent REL ASYNC asynchronous non-transparent REL SYNC synchronous non-transparent 3.2.33 AT+CRC Set Cellular Result Codes for incoming call indication AT+CRC Set Cellular Result Codes for incoming call indication Test command AT+CRC=? Read command AT+CRC? Set command AT+CRC= Response +CRC: list of supported s OK Parameters see set command Response +CRC: OK Parameters see set command Response TA controls whether or not the extended format of incoming call indication is used. OK Parameters 0 disable extended format 1 enable extended format
Page 1 and 2:
SIM300D AT Command Set SOFTWARE SPE
Page 3 and 4:
SIM300D AT Command Set Confidential
Page 5 and 6:
Page 7 and 8:
Page 9 and 10: SIM300D AT Command Set Confidential
Page 59: SIM300D AT Command Set Confidential
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
show all

SIM300D AT Command Set - Distributed Systems and Networking

Create successful ePaper yourself

Delete template?

Save as template?