Matest catalogue 2018

SECTION C | CONCRETE
293
ACCESSORIES FOR FLEXURAL 150 kN “OPEN SIDED FRAME”
C091-10 ROLLERS GROUP: lower adjustable from 75 to 525 mm,
and only one upper central roller for single point method.
C091-11 ROLLERS GROUP: lower adjustable from 75 to 525 mm,
and upper adjustable from 75 to 180 mm for two points
method.
C091-12 ROLLERS GROUP: lower adjustable from 75 to 1325 mm,
and upper adjustable from 75 to 575 mm for two points
method.
C091-14 ROLLERS GROUP: lower adjustable from 75 to 1325 mm,
and only one upper central roller for single point method.
C091-13 UPPER TAMPER (steel made), for
concrete KERBS tests.
The tamper is mounted on a
rotating coupling and fixed to the
upper part of the machine to apply
C091-13
a flexural strength on three points
on the kerb, without any torsional
stress. STANDARD: EN 1340
C090-15 DEFLECTION MEASUREMENT TEST on fiber reinforced
concrete beams 100x100x400(500) mm and
150x150x500(600) mm
STANDARDS: EN 14488-3 | ASTM C1609, C1018
The test is performed with the specific equipment (deflection
measurement device, displacement transducers)
described at pag. 305 and the automatic servocontrolled
system of load and displacement Servo-Strain (see p. 282)
C097-01 DUAL LOW CAPACITY DIGITAL RANGE, complete with
appropriate pressure transducer, only for digital
machines. Range selectable from 10 kN to 100 kN.
Technical details: see p. 313
C097-01
C097-05 CALIBRATION CLASS 1, starting from 1% of the full
range. With a special calibration procedure it is possible
to grant Class 1 practically on the full range of the
flexural machine. Applicable only on digital machines.
C100
SPLITTING TENSILE test device for cylinders.
EN 12390-6 | ASTM C496
Technical details and other
models: see p. 314
C103 SPLITTING TENSILE test
device for self blocking
pavers and cubes.
EN 1338, 12390-6.
Technical details: see p. 314
AS AN ALTERNATIVE:
C100
C103-02 SPLITTING TENSILE test
C103
device for self blocking pavers and cubes,
max dimensions 300x500 mm.
EN 1338, 12390-6. Technical details: see p. 314
E170 COMPRESSION DEVICE to test mortar specimens
40.1x40 mm EN 196 | ASTM C349
Technical details and other models: see p. 315
E172-01 FLEXURE DEVICE for mortar prisms 40.1x40x160 mm
EN 196 / EN 1015 (it can be used only with the dual low
capacity digital range 0-15kN). Technical details and
other models: see p. 428
C090-15
C093-11
C093-11 DEVICE for flexural tests on clay blocks for flooring.
STANDARDS: EN 15037-2, 15037-3 | UNI 9730-3
C127N
GRAPHIC PRINTER on thermo-paper on board for digital
models
C127-11 THERMO-PAPER roll for printer (pack of 10 rolls)
C115-01 TWO WAY HYDRAULIC VALVE,
connected to the motorized
pumping unit of the machine
to activate a second frame.
Technical details: see p. 318
C115-01
C099N NEW
INVERTER DEVICE
Applicable only on Cyber-Plus and
Servo-Plus Evolution machines.
Technical details: see p. 223
C099N
SOFTWARE for DIGITEC / AUTOTEC
or CYBER / SERVO PLUS models
C109-15 (N)* SOFTWARE for deflection measurement test
C109-16 (N)* SOFTWARE for flexural tests on clay blocks
C123 (N)* SOFTWARE Servonet for remote control
through PC
C109-11 (N)* SOFTWARE for flexural tests
C109-12 (N)* SOFTWARE for splitting tensile
Technical detail: see p. 18
(N)* for Cyber - Servo Plus models.