CCNA 3 Labs and Study Guide - BINARYBB.INFO – @jagalbraith

More documents

Recommendations

Info

414 Switching Basics and Intermediate Routing CCNA 3 Labs and Study Guide Task 7: Assign Ports to VLAN 10 You must assign ports to VLANs from the interface mode. Enter the following commands to add ports 0/4 to 0/6 to VLAN 10: Switch_A#configure terminal Switch_A(config)#interface fastethernet 0/4 Switch_A(config-if)#switchport mode access Switch_A(config-if)#switchport access vlan 10 Switch_A(config-if)#interface fastethernet 0/5 Switch_A(config-if)#switchport mode access Switch_A(config-if)#switchport access vlan 10 Switch_A(config-if)#interface fastethernet 0/6 Switch_A(config-if)#switchport mode access Switch_A(config-if)#switchport access vlan 10 Switch_A(config-if)#end Note: Use the range parameter to quickly configure several interfaces with the same command. For example: Switch_A#configure terminal Switch_A(config)#interface range fastethernet 0/4 - 6 Switch_A(config-if-range)#switchport mode access Switch_A(config-if-range)#switchport access vlan 10 Switch_A(config-if-range)#end Task 8: Assign Ports to VLAN 20 Enter the following commands to add ports 0/7 to 0/9 to VLAN 20: Switch_A#configure terminal Switch_A(config)#interface fastethernet 0/7 Switch_A(config-if)#switchport mode access Switch_A(config-if)#switchport access vlan 20 Switch_A(config-if)#interface fastethernet 0/8 Switch_A(config-if)#switchport mode access Switch_A(config-if)#switchport access vlan 20 Switch_A(config-if)#interface fastethernet 0/9 Switch_A(config-if)#switchport mode access Switch_A(config-if)#switchport access vlan 20 Switch_A(config-if)#end Task 9: Assign Ports to VLAN 30 Enter the following commands to add ports 0/10 to 0/12 to VLAN 30: Switch_A#configure terminal Switch_A(config)#interface fastethernet 0/10 Switch_A(config-if)#switchport mode access Switch_A(config-if)#switchport access vlan 30 Switch_A(config-if)#interface fastethernet 0/11 Switch_A(config-if)#switchport mode access
Page 2:
Switching Basics and Intermediate R
Page 6:
Trademark Acknowledgments All terms
Page 10:
Dedications To my wife Becky, and m
Page 14:
Contents at a Glance Chapter 1: Int
Page 18:
Task 16: Configure the Fast Etherne
Page 22:
DR/BDR Election Exercise 114 Journa
Page 26:
Comprehensive Lab 2-7: OSPF Configu
Page 30:
LAN Switches 237 Vocabulary Exercis
Page 34:
Task 3: Verify Connectivity 283 Tas
Page 38:
Task 5: Look at the Switches’ Spa
Page 42:
Task 2: Configure the Hosts Attache
Page 46:
Challenge Lab 9-6: Advanced Switchi
Page 50:
Introduction Switching Basics and I
Page 54:
Work through the Study Guide and La
Page 58:
CHAPTER 1 Introduction to Classless
Page 62:
Vocabulary Exercise: Matching Chapt
Page 66:
Class C Subnetting Scenario Use the
Page 70:
Prefix Length Use Exercises Use the
Page 74:
2. 192.168.35.142/29 IP address 110
Page 78:
4. Use subnet 4 from the last quest
Page 82:
Figure 1-1 Addressing Design Exerci
Page 86:
List the address space that is stil
Page 90:
Figure 1-7 Addressing Design Scenar
Page 94:
VLSM Addressing Design Scenario 3 C
Page 98:
Device Interface IP Address Subnet
Page 102:
For the solution shown in Figure 1-
Page 106:
First IP 192.168.1.0 11000000.10101
Page 110:
Figure 1-17 Summary Route Exercise
Page 114:
Figure 1-19 Summary Route Exercise
Page 118:
Concept Questions List at least thr
Page 122:
Figure 1-22 Mom and Pop’s Stop &
Page 126:
Students should be well versed in u
Page 130:
Lab Exercises Command Reference In
Page 134:
Table 1-2 IP Address Range for 192.
Page 138:
Table 1-8 IP Address Range for 192.
Page 142:
To finish our visual, we label all
Page 146:
Task 1: Basic Router Configuration
Page 150:
Figure 1-29 HyperTerminal Interface
Page 154:
Task 8: Configure Hostname and Pass
Page 158:
Task 17: Configure the IP Host Stat
Page 162:
Curriculum Lab 1-3: Converting RIPv
Page 166:
BHM(config)#interface serial 0 BHM(
Page 170:
Curriculum Lab 1-4: Verifying RIPv2
Page 174:
Task 7: Verify that the Internetwor
Page 178:
Have they changed now that RIPv2 is
Page 182:
i - IS-IS, L1 - IS-IS level-1, L2 -
Page 186:
Redistributing: rip Default version
Page 190:
The enable, VTY, and console passwo
Page 194:
policy Policy routing rip RIP proto
Page 198:
Will the routing table be updated t
Page 202:
Objectives ■ Review basic router
Page 206:
Task 3: Verify Connectivity Step 1.
Page 210:
RTA have a default route. ISP canno
Page 214:
area E1 - OSPF external type 1, E2
Page 218:
! logging synchronous login end RTA
Page 222:
! no shutdown interface Serial0/0 !
Page 226:
! line con 0 exec-timeout 30 0 pass
Page 230:
Step 2. Each simulated LAN requires
Page 234:
C 10.1.8.128 is directly connected,
Page 238:
RTA(config-if)#ip summary-address r
Page 242:
Now configure RTB to summarize the
Page 246:
password cisco logging synchronous
Page 250:
ip host ISP 209.165.201.1 ip host R
Page 254:
CHAPTER 2 Single-Area OSPF The Stud
Page 258:
Vocabulary Exercise: Completion Com
Page 262:
The term link simply refers to the
Page 266:
Figure 2-1d Loop-free Topology for
Page 270:
Learn the OSPF Commands Exercise 1.
Page 274:
11. The DR/BDR election is based on
Page 278:
The Cisco IOS uses the 10 8 /bps fo
Page 282:
Figure 2-6 Propagating a Default Ro
Page 286:
Network DR/BDR Election? Which Rout
Page 290:
Command Description Router#show ip
Page 294:
BERLIN Router>enable Router#configu
Page 298:
Step 3. Ping from one of the connec
Page 302:
Table 2-3 Lab Equipment Configurati
Page 306:
BRASILIA(config-line)#login BRASILI
Page 310:
Are entries in the routing table? N
Page 314:
Task 14: Verify OSPF Interface Conf
Page 318:
Objectives ■ Set up an IP address
Page 322:
Step 2. Each workstation should be
Page 326:
Step 2. Examine the running configu
Page 330:
Step 5. Verify or explain the previ
Page 334:
Dublin(config-line)#password cisco
Page 338:
Washington(config)#router ospf 1 Wa
Page 342:
Curriculum Lab 2-5: Configuring OSP
Page 346:
Sydney(config)#ip host Rome 192.168
Page 350:
Task 7: Observe OSPF Traffic Step 1
Page 354:
After you complete the previous ste
Page 358:
Task 2: Configure the Area 0 OSPF R
Page 362:
Task 5: Verify Connectivity Ping fr
Page 366:
Task 11: Verify Connectivity from t
Page 370:
Equipment The topology shown in Fig
Page 374:
Success rate is 100 percent (5/5),
Page 378:
Number of interfaces in this area i
Page 382:
no ip domain-lookup ip host RTB 192
Page 386:
! interface Serial0/1 ! description
Page 390:
exec-timeout 0 0 password cisco log
Page 394:
Table 2-16 LAN Addressing Specifica
Page 398:
login line vty 0 4 ! exec-timeout 0
Page 402:
hostname REMOTE ! enable secret cla
Page 406:
CHAPTER 3 EIGRP and Troubleshooting
Page 410:
Vocabulary Exercise: Completion Dir
Page 414:
RTA(config)#router eigrp 100 RTA(co
Page 418:
C 172.16.0.0/18 is directly connect
Page 422:
In the shaded entry for 192.168.1.1
Page 426:
Troubleshooting EIGRP Normal EIGRP
Page 430:
P 172.16.0.0/18, 1 successors, FD i
Page 434:
It means that this router is runnin
Page 438:
Internet Research Exercise The CCNA
Page 442:
Protocol Value Network Layer Protoc
Page 446:
Curriculum Lab 3-1: Configuring EIG
Page 450:
PARIS(config-if)#exit PARIS(config)
Page 454:
Task 6: Configure EIGRP Routing on
Page 458:
PARIS(config)#line console 0 PARIS(
Page 462:
Task 5: Configure EIGRP Routing on
Page 466:
Table 3-5 Addressing Table for Lab
Page 470:
RTB RTC RTB(config)#interface Loopb
Page 474:
What command would you configure on
Page 478:
Step 2. Starting with 10.0.64.0, co
Page 482:
! ip address 10.0.80.1 255.255.240.
Page 486:
via 10.0.0.6 (2297856/128256), Seri
Page 490:
H Address Interface Hold Uptime SRT
Page 494:
CHAPTER 4 Switching Concepts The St
Page 498:
Vocabulary Exercise: Matching Defin
Page 502:
CSMA/CD Process Flow Chart Exercise
Page 506:
Introduction to LAN Switching In th
Page 510:
Concept Questions Explain the diffe
Page 514:
Figure 4-6 Collision and Broadcast
Page 518:
Lab Exercises There are no Lab Exer
Page 522:
CHAPTER 5 LAN Design and Switches T
Page 526:
Page 530:
List and briefly explain the four s
Page 534:
Figure 5-5 Scenario 4 In Figure 5-5
Page 538:
Lab Exercises There are no Lab Exer
Page 542:
CHAPTER 6 Catalyst Switch Configura
Page 546:
Switch LED Interpretation Exercise
Page 550:
Figure 6-2 Basic Switch Configurati
Page 554:
Lab Exercises Command Reference In
Page 558:
Table 6-1 shows the switch command
Page 562:
or #show interface ethernet 0/4 Not
Page 566:
Curriculum Lab 6-2: Basic Switch Co
Page 570:
interface FastEthernet0/2 no ip add
Page 574:
Task 4: Examine the Current Running
Page 578:
Task 5: Set the Access Passwords (1
Page 582:
Step 3. Set the port speed of inter
Page 586:
interface FastEthernet0/3 ! interfa
Page 590:
Step 3. Type the switch IP address
Page 594:
Task 6: Determine the show mac-addr
Page 598:
Why did this change from the last d
Page 602:
Task 5: Determine the MAC Addresses
Page 606:
Task 10: Verify the Results Verify
Page 610:
If you are running Windows 2000, ch
Page 614:
Task 10: Verify the Results Step 1.
Page 618:
000a.b772.2b44) MTU 1500 bytes, BW
Page 622:
Task 1: Configure the Switch Config
Page 626:
All 0100.0cdd.dddd STATIC CPU 1 000
Page 630:
Step 4. Record the VLAN 1 MAC addre
Page 634:
Task 17: Exit the Switch Step 1. Ex
Page 638:
Step 2. After the TFTP server is ru
Page 642:
(fc1) Copyright 1986-2004 by cisco
Page 646:
Table 6-8 Lab Equipment Configurati
Page 650:
Step 3. From the console session in
Page 654:
! interface FastEthernet0/7 ! inter
Page 658:
Background/Preparation Cable a netw
Page 662:
Task 7: Procedure for the 1900 and
Page 666:
Curriculum Lab 6-10: Firmware Upgra
Page 670:
Task 5: Prepare for the New Image S
Page 674:
Equipment The topology shown in Fig
Page 678:
Step 3. What commands can you use t
Page 682:
CHAPTER 7 Spanning Tree Protocol Th
Page 686:
Journal Entry Chapter 7: Spanning T
Page 690:
Page 694:
Figure 7-2 Determine the Root Bridg
Page 698:
Figure 7-4 Determine the Root Bridg
Page 702:
Concept Questions What are the basi
Page 706:
The enable, VTY, and console passwo
Page 710:
Task 5: Look at the VLAN Interface
Page 714:
What is the priority of the non-roo
Page 718:
Which ports are forwarding on the r
Page 722:
Objectives ■ Create a basic switc
Page 726:
hello 2, max age 20, forward delay
Page 730:
Task 7: Look at the Spanning-Tree T
Page 734:
———————— ———
Page 738:
CHAPTER 8 Virtual LANs The Study Gu
Page 742:
True SWA(config)#interface fa0/4 SW
Page 746:
VLAN global configuration mode Swit
Page 750:
Switch#show vlan brief VLAN Name St
Page 754:
The enable secret password is class
Page 758:
1002 fddi-default act/unsup 1003 to
Page 762:
Task 9: Display the VLAN Interface
Page 766:
VLAN Type SAID MTU Parent RingNo Br
Page 770:
■ Name the VLANs and assign multi
Page 774:
Switch_A(config-if)#switchport mode
Page 778:
VLAN Type SAID MTU Parent RingNo Br
Page 782:
Why? They have different VLAN membe
Page 786:
1005 trnet 101005 1500 - - - ibm -
Page 790:
Switch_A(config-if)#switchport acce
Page 794:
Switch_A#show vlan VLAN Name Status
Page 798:
A default VLAN may not be deleted.
Page 802:
30 Purchasing active Fa0/17, Fa0/18
Page 806:
Total Addresses in System : 0 Max A
Page 810:
! end SWB !————————
Page 814:
CHAPTER 9 VLAN Trunking Protocol Th
Page 818:
Chapter 9: VLAN Trunking Protocol 3
Page 822:
Vocabulary Exercise: Completion Dir
Page 826:
List and describe the three types o
Page 830:
List three possible ways to reset t
Page 834: Lab Exercises Command Reference In
Page 838: Curriculum Lab 9-1: Trunking with I
Page 842: 1002 fddi-default act/unsup 1003 to
Page 846: Switch_A(config-if)#interface faste
Page 850: Trunking Native Mode VLAN: 1 (defau
Page 854: Step 1. To test the VLANs and the t
Page 858: interface FastEthernet0/10 switchpo
Page 862: Cable a network that is similar to
Page 866: Switch_A(config-if)#switchport acce
Page 870: Why? No trunk has been configured y
Page 874: Task 16: Test the VLANs and the Tru
Page 878: Curriculum Lab 9-3: VTP Client and
Page 882: 1005 trnet 101005 1500 - - - ibm -
Page 888: 416 Switching Basics and Intermedia
Page 936:
440 Switching Basics and Intermedia
Page 940:
Page 944:
Page 948:
Page 952:
Page 956:
Page 960:
Page 964:
Page 968:
Page 972:
Page 976:
Page 980:
Page 984:
Page 988:
Page 992:
Page 996:
This page intentionally left blank
Page 1000:
Page 1004:
This page intentionally left blank
Page 1008:
Page 1012:
Page 1016:
Page 1020:
Page 1024:
Page 1028:
Page 1032:
Page 1036:
Page 1040:
Page 1044:
Page 1048:
Page 1052:
Page 1056:
Page 1060:
Page 1064:
Page 1068:
Page 1072:
Page 1076:
Page 1080:
Page 1084:
Page 1088:
Page 1092:
Page 1096:
Page 1100:
show all

CCNA 3 Labs and Study Guide - BINARYBB.INFO – @jagalbraith

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?