manual de instalação e utilização transmissor console ... - Usicontrol

More documents

Recommendations

Info

The ramp speed is defined for each semiaxis by a parameter that can take a value between 0 and 15, by default 0. Each of these values corresponds to a ramp time from minimum to maximum value given by the following table: 0 without ramp 4 0,4 s 8 1,0 s 12 2,0 s 1 0,1 s 5 0,5 s 9 1,2 s 13 2,5 s 2 0,2 s 6 0,6 s 10 1,5 s 14 3,5 s 3 0,3 s 7 0,8 s 11 1,7 s 15 5,0 s Through Tele-Alignment can set the maximum and minimum values, the polarity inversion, acceleration or deceleration ramp and curve type of the analogue output. To change to Tele-Alignment mode is necessary to introduce a bridge in the jumper P6 (see Jumpers configuration). Only available for TM70 consol box from 3.1 software version or higher. Other features of the PWM current outputs: Power supply range of the expansion 8-30V, and of the outputs 5-35V. Max current = 10 mA (each output). Outputs protected against short-circuit. 20.2- CONNECTIONS & JUMPERS CONFIGURATION CONNECTIONS WITH THE LR72 The expansion connects to the LR72 electronic board through two connectors, one of 2 pin for power supply (VI + and GND) and the other of 5 pin for the CAN bus with the following signals: OUTPUTS Power connector Pin number Function GND Ground +VI DC between 8 y 30V CAN bus connector Name Function VCAN Power supply CANH CANH pin of the CAN bus GNDCAN Ground CANL CANL pin of the CAN bus GNDCAN Ground The voltage outputs are generated from PWM pulses, and them filtered result in radiometric tension outputs (dependent on supply voltage). The two outputs are electrically isolated respect to the logic and each other. The control of relays is done via VREL1 and VREL2 signals. Also, it needs to be activated the common of both relays by VCOMREL signal. When the relays are off, the output voltage VO1 and VO2 are the values of reference voltage VR1 and VR2 connected at each output. The output values range goes from 0 to 100% of power supplies VPP1 and VPP2 connected to each of the outputs and have a resolution of 10 bits (1024 values). TM70Pi V3.2 (11/02) 120021.pdf. 86 IKUSI reserves the right to change this information without prior notice.
OUTPUT 1 (VO1) The connections of the output 1 are through 4 pole terminal plug, with the follow pin assignment: Output 1 connector OUTPUT 2 (VO2) Pin Name Function VPP1 Power of channel 1 GND1 Ground of channel 1 VO1 Analogue output of channel 1 VR1 Zero position signal signal to get through the output 1 when the relay is inactive The connections of the output 1 are through 4 pole terminal plug, with the follow pin assignment: Output 2 connector Pin name Function VPP2 Power of channel 2 GND2 Ground of channel 2 VO2 Analogue output of channel 2 VR2 Zero position signal signal to get through the output 2 when the relay is inactive ISP (PROGRAMACION “IN CIRCUIT” / “IN SYSTEM”) The expansion has a connector to record ―In-System‖ (eg. Microprocessor software update). This connector has 10 pins: ISP connector Pin name Function ISP2 Input connected to the ground to place the microcontroller in recording mode TX2 Not used RX2 Receiving data signal GND Ground RX1 Receiving data signal TX1 Transmisión data signal ISP Not used VCC Power supply output at 3,3 V MRNOT Reset input, active when it is connected to ground +VI Power supply output at 12 V (not stabilized, can vary between 8 y 22 V) TM70Pi V3.2 (11/02) 120021.pdf. 87 IKUSI reserves the right to change this information without prior notice.
Page 1 and 2:
MANUAL DE INSTALAÇÃO E UTILIZAÇ
Page 3 and 4:
11.- OPÇÃO LIMITADOR DE ALCANCE L
Page 5 and 6:
1.- DECLARAÇÃO DE CONFORMIDADE (B
Page 7 and 8:
3.- DESCRIÇÃO DO SISTEMA Os contr
Page 9 and 10:
4.3 - RECOMENDACIONES FCC (Sólo v
Page 11 and 12:
5.2 - RECEPTOR Promover a parada to
Page 13 and 14:
5.3- INÍCIO DE OPERAÇÃO Seja pre
Page 15 and 16:
6.- UTILIZAÇÃO Para uma correta u
Page 17 and 18:
7.3 - LOCALIZAÇÃO DE AVARIAS O em
Page 19 and 20:
ANEXO A - PROGRAMAÇÃO DO EMISSOR
Page 21 and 22:
ANEXO C - MUDANÇA DE CANAL BASE. O
Page 23 and 24:
8.1 - INTRODUCCIÓN El equipo TM70
Page 25 and 26:
100D: LIFE TIME FACTOR 1014: COB-ID
Page 27 and 28:
8.5 - DICCIONARIO DE DATOS DEL RECE
Page 29 and 30:
8.6 - SEÑALIZACIÓN El receptor di
Page 31 and 32:
Mantenimiento y localización de er
Page 33 and 34:
9.1 - INTRODUCCIÓN y DESCRIPCION F
Page 35 and 36:
9.3 - EXPLOSIONADO DE ENSAMBLAJE T7
Page 37 and 38:
9.5 - MODO RETORNO DE INFORMACION L
Page 39 and 40:
9.5.2 ICONOS DISPONIBLES Los iconos
Page 41 and 42:
Ejemplo: Retorno CAN VT100 Escribir
Page 43 and 44:
Una vez completados los 24 caracter
Page 45 and 46:
10. TM70 - OPERACIONES EN MODO FIRS
Page 47 and 48:
11.1.1- DESCRIPCIÓN DEL SISTEMA Lo
Page 49 and 50:
11.2.2 - INSTALACION Y CONEXIONADO
Page 51 and 52:
11.3.1 - EMISOR INFRARROJO LA70M Nu
Page 53 and 54:
Area de cobertura elíptica de la e
Page 55 and 56:
12.- MODO DE FUNCIONAMIENTO “PITC
Page 57 and 58:
Los emisores no disponen de ningún
Page 59 and 60:
13. TM70 - OPERACIONES EN TANDEM 13
Page 61 and 62:
13.3.- SISTEMAS CON DOS EMISORES MA
Page 63 and 64:
14. TM70 - OPERACIONES CON VIA DE R
Page 65 and 66:
14.3- MONTAJE EXPANSION IN0-10V CON
Page 67 and 68:
15.1 - INTRODUCCIÓN y DESCRIPCION
Page 69 and 70:
16.- OPCION IN4D OPCION IN4D TM70 T
Page 71 and 72:
En caso de no disponer una tensión
Page 73 and 74:
16.2.- CONEXIÓN CON LR71 y LR72 2.
Page 75 and 76:
17.1- INTRODUCCION y DESCRIPCION FU
Page 77 and 78:
18.- OPCION A1P4RCAN OPCION A1P4RCA
Page 79 and 80:
SALIDAS DE RELÉS RL2 RL3 +VI GND 1
Page 81 and 82:
19.- OPCION A2ICAN OPCION A2ICAN TM
Page 83 and 84:
La velocidad de rampa se define par
Page 85 and 86:
JUMPERS DE CONFIGURACION Tamaño ¼
Page 87 and 88:
20.1- INTRODUCCIÓN Y DESCRIPCIÓN
Page 89 and 90:
El rango de los valores de salida o
Page 91 and 92:
20.3- TARJETA DE ALIMENTACIÓN DE E
Page 93 and 94:
21.1- INTRODUCCIÓN El acceso a est
Page 95 and 96:
(*) SI FREQ. PWM = 0 (ALTA FRECUENC
Page 97 and 98:
VALORES LIMIT: Ajuste de los valore
Page 99 and 100:
21.2.2- MENU 3.2 VAL. FÁBRICA: Imp
Page 101 and 102:
22.1 - CARACTERISTICAS PRINCIPALES
Page 103 and 104:
OPCION 4: Relación de tipos de exp
Page 105 and 106:
22.2 - OBSERVACIONES PARA EL CABLEA
Page 107 and 108:
CHINA 北京市朝阳区望京阜
Page 109 and 110:
I N D I C E 1.- DECLARATION OF CONF
Page 111 and 112:
TM70Pi V3.2 (11/02) 120021.pdf. iii
Page 113 and 114:
2. - DECLARATION OF CONFORMITY (433
Page 115 and 116:
4.- SAFETY INSTRUCTIONS These instr
Page 117 and 118:
5.- INSTALLATION 5.1 - CB70 (BC70K)
Page 119 and 120:
Connect the power supply and the re
Page 121 and 122:
Next, turn transmitter ON to OPERAT
Page 123 and 124:
7.- MAINTENANCE 7.1 - WARRANTY 7.2
Page 125 and 126:
There are also two LEDs in the rece
Page 127 and 128:
ANNEX B.- PROGRAMMING THE MACHINE I
Page 129 and 130:
8.- CAN OPEN INTERFACE V 2.4 CANope
Page 131 and 132:
The LED signalling is the one recom
Page 133 and 134:
8.4 - PUSHBUTTONS AND CONSOLE BOX P
Page 135 and 136:
CONSOLE BOX: The receiver can accep
Page 137 and 138:
Connections scheme : Receiver‟s d
Page 139 and 140:
9.- LCD70 DISPLAY OPTION LCD70 DISP
Page 141 and 142:
9.2 - INTERNAL CONNECTION POWER SUP
Page 143 and 144:
TM70Pi V3.2 (11/02) 120021.pdf. 31
Page 145 and 146:
9.5 - DATA FEEDBACK OPERATING MODE
Page 147 and 148: 9.5.2 AVAILABLE ICONS: The availabl
Page 149 and 150: Example: VT100 data feedback Write
Page 151 and 152: Once that we have completed the 24
Page 153 and 154: TM70 - “FIRST COME - FIRST SERVED
Page 155 and 156: 11.1.1 - SYSTEM DESCRIPTION TM70 ra
Page 157 and 158: In cases in which it is believed th
Page 159 and 160: In cases in which the area covered
Page 161 and 162: Module: LA70M EX SPECIFICATIONS DC
Page 163 and 164: 11.3.2.- LA70M INSTALLATION AND CON
Page 165 and 166: TM70 - “PITCH & CATCH” OPERATIO
Page 167 and 168: 13.- TANDEM OPERATION TANDEM OPERAT
Page 169 and 170: 13.2 - ONE MASTER TRANSMITTER SYSTE
Page 171 and 172: 14.- ANALOGUE FEEDBACK / IN 0-10V O
Page 173 and 174: 8. Press ―ENTER‖ function. 9. I
Page 175 and 176: 15.- IN0450P OPTION IN0450P OPTION
Page 177 and 178: 15.2 - IN0450P and LR70 ASSEMBLY IN
Page 179 and 180: 16.1 - INTRODUCTION AND FUNCTIONAL
Page 181 and 182: Electronic card top view (see figur
Page 183 and 184: 17.- INCAN OPTION INCAN OPTION TM70
Page 185 and 186: RL4 Pin Name Function + +VI DC powe
Page 187 and 188: 18.1.- INTRODUCTION and FUNCTIONAL
Page 189 and 190: ANALOGUE OUTPUT The analogue output
Page 191 and 192: 19.1- INTRODUCTION & FUNCTIONAL DES
Page 193 and 194: OUTPUTS Each analogue output has tw
Page 195 and 196: TM70Pi V3.2 (11/02) 120021.pdf. 83
Page 197: 20.1- INTRODUCTION & FUNCTIONAL DES
Page 201 and 202: 20.3- EXPANSIONS POWER SUPPLY ELECT
Page 203 and 204: 21.1 - INTRODUCTION Access to this
Page 205 and 206: (*) IF PWM FREQ. = 0 (HIGH FREQUENC
Page 207 and 208: LIMIT VALUES: Set the limits of the
Page 209 and 210: 2.2 - MENU 3.2 RESET VALUES: Restor
Page 211 and 212: 22.1 - MAIN CHARACTERISTICS Softwar
Page 213 and 214: OPTION 4: List of expansión type a
Page 215 and 216: 22.2 - REMARKS FOR THE INTERNAL WIR
Page 217: CHINA 北京市朝阳区望京阜
show all

manual de instalação e utilização transmissor console ... - Usicontrol

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?