HP iLO 3 Scripting and Command Line Guide - Business Support ...
HP iLO 3 Scripting and Command Line Guide - Business Support ...
HP iLO 3 Scripting and Command Line Guide - Business Support ...
Sie wollen auch ein ePaper? Erhöhen Sie die Reichweite Ihrer Titel.
YUMPU macht aus Druck-PDFs automatisch weboptimierte ePaper, die Google liebt.
System properties <strong>and</strong> targets<br />
The properties <strong>and</strong> targets described in this section provide information about the server.<br />
Table 19 (page 52) shows the System targets. Table 20 (page 53) shows the System properties.<br />
System properties settings are available at:<br />
/system1/oemhp_power1<br />
Table 19 System Targets<br />
Target<br />
oemhp_PresentPower<br />
oemhp_AvgPower<br />
oemhp_MaxPower<br />
oemhp_MinPower<br />
warning_type<br />
warning_threshold<br />
warning_duration<br />
oemhp_powerreg<br />
oemhp_pwrcap<br />
oemhp_powersupplycapacity<br />
oemhp_servermaxpower<br />
oemhp_serverminpower<br />
oemhp_power_micro_ver<br />
oemhp_auto_pwr<br />
Verbs:<br />
• cd<br />
• version<br />
• exit<br />
• show<br />
• set<br />
For example:<br />
Description<br />
Displays the average power reading from the last sample<br />
Displays the average power reading from the past 24 hours<br />
Displays the greatest peak power reading from the past 24 hours<br />
Displays the minimum average power reading from the past 24 hours<br />
Displays <strong>and</strong> modifies the warning type<br />
Displays <strong>and</strong> modifies the warning threshold for power consumption<br />
Displays <strong>and</strong> modifies the duration the power threshold must be exceeded before a<br />
warning is generated<br />
Displays <strong>and</strong> modifies the Power Regulator for ProLiant state. Valid values are dynamic,<br />
max, min, or os.<br />
Displays <strong>and</strong> modifies the power cap setting for the server in watts. A wattage of<br />
zero indicates that power capping is disabled. The value must be an integer cap<br />
value that is greater than or equal to oemhp_serverminpower, <strong>and</strong> must be less than<br />
or equal to oemhp_powersupplycapacity.<br />
Displays the power supply's total capacity in Watts.<br />
Displays the server's maximum power capacity in Watts.<br />
Displays the server's minimum power capacity in Watts.<br />
Displays the firmware version number for the Power Micro Controller.<br />
Displays <strong>and</strong> modifies Server Automatic Power On setting. Valid values are on,<br />
restore, <strong>and</strong> off. On turns on automatic power on with minimum delay. Restore restores<br />
the last power state (ML/DL servers only). Off turns off automatic power on.<br />
• show /system1/oemhp_power1 oemhp_powerreg<br />
• set /system1/oemhp_power1 oemhp_powerreg=<br />
• show /system1/oemhp_power1 oemhp_pwrcap<br />
• set /system1/oemhp_power1 oemhp_pwrcap=0<br />
• show /system1/oemhp_power1 oemhp_power_micro_ver<br />
The following comm<strong>and</strong> shows all the properties for oemhp_power1:<br />
show /system1/oemhp_power1<br />
52 SMASH CLP <strong>Scripting</strong> Language