Enabler-G AT Command Set - SE Spezial-Electronic AG

More documents

Recommendations

Info

AT Command Set Reference Version 1.08 3.2.9.1. $EVENT User Defined Input/Output (continued) Real Time Clock Output Event 46 Set RTC On/Off time. Parm1 sets the RTC ON time in minutes while Parm2 sets the OFF time in mins Event Counter 47 Event Counter. Counts occurrences of an event till the number specified by parm2 (parm1 is not used). The input event 51 is generated when maximum number is reached. GSM0107PB001MAN Page 267 of 370 1.08 – 25 January 2007
AT Command Set Reference Version 1.08 3.2.9.1. $EVENT User Defined Input/Output (continued) parameter values Event Type Event Category Result Input, transition, occurrence Input State Event Defines the valid start range Input, Modem Status Defines the valid start range transition, occurrence Event Input, Input Timer Defines the valid start range transition, occurrence Event Output, Output State Parm1 is ignored transition, occurrence Event Output Output Transition Event Parm1 is ignored Output Output Flash Bits 16 – 31 determine the low signal Event state while bits 0 – 15 determine the high signal state. A value of 0 for bits 16 – 31 indicates the GPIO will remain in low signal state for the same amount of time as the as the high signal state (50% duty cycle). The high or low states are measured in multiples of ¼ seconds. The toggle count is set by Parm2. Output Output Message parm1 is a special user message Event identification. The 32-bit number entered can be used to dynamically generate intelligent messages. It will be the first 4 bytes of data following the API header in the output message. An example of using this field would be to designate the bytes as unique identifiers. Bytes 1 and 2 could identify the device, byte 3 could define the message format, and byte 4 could provide the event group that triggered the message. Output Output Reset Parm1 defines the timer (1 – 4) to be Timer Event reset. GSM0107PB001MAN Page 268 of 370 1.08 – 25 January 2007
Page 1 and 2:
GSM0107PB001MAN Enfora Enabler-IIG
Page 3 and 4:
AT Command Set Reference Version 1.
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226: AT Command Set Reference Version 1.
Page 275: AT Command Set Reference Version 1.
Page 327 and 328:
Page 329 and 330:
Page 331 and 332:
Page 333 and 334:
Page 335 and 336:
Page 337 and 338:
Page 339 and 340:
Page 341 and 342:
Page 343 and 344:
Page 345 and 346:
Page 347 and 348:
Page 349 and 350:
Page 351 and 352:
Page 353 and 354:
Page 355 and 356:
Page 357 and 358:
Page 359 and 360:
Page 361 and 362:
Page 363 and 364:
Page 365 and 366:
Page 367 and 368:
Page 369 and 370:
show all

Enabler-G AT Command Set - SE Spezial-Electronic AG

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?