Enabler-G AT Command Set - SE Spezial-Electronic AG

More documents

Recommendations

Info

AT Command Set Reference Version 1.08 3.2.9.7. $MSGLOGAL Message Log Alarm $MSGLOGAL Send an Alarm message when Message Log buffer trigger conditions are violated Command Function This command allows a user to set trigger conditions and send a message when conditions are violated Command Functional Group Enfora Specific Command Format Query AT$MSGLOGAL=? Response $MSGLOGAL: (0–100),(0-10000),(0-4) OK Write Format Response AT$MSGLOGAL=,, Read Format Response AT$MSGLOGAL? $MSGLOGAL: 0,0,0 OK Execution Format Response N/A Parameter Values This field specifies the trigger condition when x Percentage of the message log buffer is filled with unsent messages. Valid values for this parameter are 0 – 100 % positive integer values only. Maximum number of messages stored in the message log buffer before sending a msg log alarm message. Valid values for this parameter are 0 – 10000 messages. Note, the maximum number of messages stored in the buffer depends on the message length. This does not imply that one can store 10,000 messages of any length. Maximum buffer size is 50Kbytes. GSM0107PB001MAN Page 281 of 370 1.08 – 25 January 2007
AT Command Set Reference Version 1.08 3.2.9.7. $MSGLOGAL Message Log Alarm (continued) This parameter specifies the medium/transport used to send the alarm message 0 = send alarm message out the serial port 1 = send alarm message via SMS to addresses specified by $smsda command 2 = send alarm message via UDP to address specified by $friend command 4 = send alarm message via TCP to address specified by $friend command Reference N/A Standard Scope Optional Enfora Implementation Scope Full Notes The alarm message will have the following format: ,,. Example: Send the following command at$msglogal=1,0,0 to enable message log alarm when 1% of memory is full with unsent messages. When alarm condition is triggered, you should see a message similar to this: “010754000056580,55399,12” over the serial port where “010754000056580” is the modem ID of the device, “55399” is the number of bytes available to store messages, and “12” is the number of unsent messages currently stored in buffer. A new alarm message is sent only after the current alarm condition is cleared. GSM0107PB001MAN Page 282 of 370 1.08 – 25 January 2007
Page 1 and 2:
GSM0107PB001MAN Enfora Enabler-IIG
Page 3 and 4:
AT Command Set Reference Version 1.
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240: AT Command Set Reference Version 1.
Page 289: AT Command Set Reference Version 1.
Page 341 and 342:
Page 343 and 344:
Page 345 and 346:
Page 347 and 348:
Page 349 and 350:
Page 351 and 352:
Page 353 and 354:
Page 355 and 356:
Page 357 and 358:
Page 359 and 360:
Page 361 and 362:
Page 363 and 364:
Page 365 and 366:
Page 367 and 368:
Page 369 and 370:
show all

Enabler-G AT Command Set - SE Spezial-Electronic AG

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?