General Information on Track Circuits - RGS Online
General Information on Track Circuits - RGS Online
General Information on Track Circuits - RGS Online
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<str<strong>on</strong>g>General</str<strong>on</strong>g> <str<strong>on</strong>g>Informati<strong>on</strong></str<strong>on</strong>g> <strong>on</strong> <strong>Track</strong> <strong>Circuits</strong><br />
9 <strong>Track</strong> Circuit<br />
Disc<strong>on</strong>necti<strong>on</strong><br />
Box<br />
Withdrawn Document<br />
Unc<strong>on</strong>trolled When Printed<br />
Railway Group Approved Code of Practice<br />
GK/RC0752<br />
Issue Two<br />
Date December 1998<br />
Page E17 of 52<br />
Move the heat–shrink sleeve until the entire stripped length of the cable is<br />
covered by the sleeve without restricting the securing hole.<br />
Apply heat to the heat–shrink sleeve. Before heating, the sleeve is 55mm l<strong>on</strong>g,<br />
and reduces to about 50mm when it is fully heat–shrunk <strong>on</strong>to the cable and the<br />
plate.<br />
Place the “L” plate assembly <strong>on</strong>to the threaded studs and secure using the<br />
remaining washers and the self locking nuts, tightened to a torque of 13 Nm.<br />
Fit the flange clip over the cable and push the clip <strong>on</strong>to the rail.<br />
The typical arrangement of the track circuit disc<strong>on</strong>necti<strong>on</strong> box is shown in Figure<br />
E13. It is mounted <strong>on</strong> a stake using two M8 studs (supplied with the box) and<br />
comprises a moulded rubber back with a slide–<strong>on</strong> metal cover which can be<br />
padlocked using the standard RKB221 padlock. Provisi<strong>on</strong> is made to securely<br />
clamp both the lineside apparatus housing tail cables and track lead cables in the<br />
base of the box. A l<strong>on</strong>ger stake is available for use where ground c<strong>on</strong>diti<strong>on</strong>s are<br />
poor.<br />
Descripti<strong>on</strong><br />
Stake (Angle), 760mm l<strong>on</strong>g, to BRS-SM 104/13 :<br />
Catalogue No.<br />
86/10751<br />
Stake (Angle), 1070mm l<strong>on</strong>g to BRS-SM 104/11 : 86/88250<br />
<strong>Track</strong> Circuit Disc<strong>on</strong>necti<strong>on</strong> Box : 86/43877<br />
The terminati<strong>on</strong> for each track circuit comprises a four way 2BA link block. The<br />
various cables should be terminated as shown in Figure E14 (this enables the<br />
individual track leads of duplicated arrangements to be disc<strong>on</strong>nected/tested<br />
separately).<br />
Note 1: Only <strong>on</strong>e track circuit is allowed in a Disc<strong>on</strong>necti<strong>on</strong> Box and hence<br />
double track circuit boxes are not to be used.<br />
Note 2: Separate tail cables must be provided for each track circuit end.<br />
Note 3: Disc<strong>on</strong>necti<strong>on</strong> Boxes should be mounted in a permanent Green Z<strong>on</strong>e<br />
as defined in GO/RT3073.<br />
R A I L T R A C K E 17