Operation and Maintenance Manual for

More documents

Recommendations

Info

LC Manual 11/02 Rev. 3 APPENDIX 7.6 COMPONENT MANUFACTURER LITERATURE Only the literature checked below that applies to your system will be included in this section. Component Manufacturer Model Number Vantage Model Pump Procon 104E240F11XX All LC-Models Membrane Filmtec TW30-2540 All LC-Models Controller RODI Systems MC10 All LC-Models Software RODI Systems Aquagraph VROLCXXXM 7-10 USFilter
Product Description/Equipment Specifications Vantage Series Reverse Osmosis Units Model LC Process Water Systems General Description USFilter’s Vantage Series model LC Reverse Osmosis units are designed and manufactured for commercial applications. Each LC model consists of a single stage centrifugal pump and tap water low pressure membranes. They are preengineered, pre-assembled units that minimize installation and start-up costs. They are fully tested at the factory and only require simple utility connections (feed water inlet, product water outlet, drains and power). They arrive with membranes installed and are ready for immediate on-line service with minimal set up and adjustments. Their simple designs maximize reliability of the Reverse Osmosis unit. An optional modem is available for remote operation and monitoring to tailor the Vantage Series Reverse Osmosis equipment for specific customer requirements. Each unit is a single pass RO system mounted on a polyurethane coated structural steel frame. The RO unit includes a high pressure feed pump, PVC end entry pressure vessels, and spiral wound thin film composite RO membranes. Each RO unit also includes PVC low pressure piping, high pressure brass fittings and nylon tube and fittings, polyethylene tube and fittings for low pressure reject, reject recycle and product piping, and a system controller. Mechanical Description The major components are supported by the frame and designed in such a way to provide easy access for servicing, maintenance, and monitoring system performance. The frame is an open style full frame configuration designed to provide maximum support and protection for the RO unit’s components and allow access for maintenance and operation. The feed piping is schedule 80 PVC. The low pressure reject, product and low pressure reject recycle is Polyethylene tubing. The high pressure manifold is constructed of threaded brass fittings and Nylon tubing and fittings. The inlet piping connection is female pipe thread PVC fittings. The product outlet, reject and autoflush connections are quick connect tube style. All high pressure valves, reject throttling and reject recycle throttling needle valves are brass. Sample valves are provided for the RO unit’s feed and product lines. An individual sample valve is also located on the product line of each pressure vessel for analyzing individual vessel performance. Cleaning connections are provided to clean the RO membranes and pressure vessels. All of the cleaning connections are quick connect tube fittings. SV301-LC_rev2.doc Page 1 Rev. 2, 10 Oct 2001
Page 1 and 2: USFilter 10 Technology Drive Lowell
Page 3 and 4: This manual discloses information i
Page 5 and 6: TABLE OF CONTENTS SECTION DESCRIPTI
Page 7 and 8: LC Manual 11/02 Rev. 3 INTRODUCTION
Page 9 and 10: LC Manual 11/02 Rev. 3 INTRODUCTION
Page 11 and 12: LC Manual 11/02 Rev. 3 SYSTEM INSTA
Page 13 and 14: LC Manual 11/02 Rev. 3 SYSTEM INSTA
Page 15 and 16: LC Manual 11/02 Rev. 3 OPERATING IN
Page 21 and 22: SYSTEM MAINTENANCE LC Manual 11/02
Page 31 and 32: TROUBLESHOOTING LC Manual 11/02 Rev
Page 33 and 34: LC Manual 11/02 Rev. 3 WARRANTY 6.1
Page 35 and 36: APPENDIX LC Manual 11/02 Rev. 3 7.1
Page 41 and 42: APPENDIX LC Manual 11/02 Rev. 3 RO
Page 43: APPENDIX LC Manual 11/02 Rev. 3 7.5
Page 47 and 48: Process Water Systems General Speci
Page 49 and 50: Process Water Systems Low feed pres
Page 51 and 52: Process Water Systems Skid Cleaning
Page 53 and 54: Series 1, 2 & 3 Pumps Page 1 of 2 [
Page 55 and 56: Product Information FILMTEC Membran
Page 57 and 58: USFilter USFilter USFilter USFilter
Page 59 and 60: Conventions and Symbols ii Special
Page 61 and 62: Table of Contents iv MC10 Overview
Page 63 and 64: Specifications The MC10 incorporate
Page 65 and 66: ! The MC10 may be configured to use
Page 67 and 68: Installation 2 Environmental The MC
Page 69 and 70: I/O The wiring diagram for the inpu
Page 71 and 72: Operation 3 Controls The MC10 is ho
Page 73 and 74: Sequence The normal startup and shu
Page 75 and 76: 7 Perm Divert TD Sec 8 High Temp SP
Page 77 and 78: Time Delays Time delays and deadban
Page 79 and 80: Important Please note: • Temperat
Page 81 and 82: Troubleshooting 5 The MC10 Reverse
Page 83 and 84: Type of Problem Possible Cause or S

Operation and Maintenance Manual for

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?