Operation and Maintenance Manual for

More documents

Recommendations

Info

with a low level tank switch (See “Settings” section of this manual). The flush cycle is also enabled in this mode. The controller will activate a flush only when the system starts. The Flush Duration is entered in the Settings menu (See “Settings” section of this manual). When the system is autoflushing, the amount of time remaining in the flush will be indicated on the third line of the display. The direct feed mode is intended to place the system in an operational mode when the system is feeding a distribution loop or another piece of equipment. In this mode the system will not flush and the tank level switch(es) is/are disregarded. When the system is in this mode, the total number of hours the system has been operated will be indicated on the last line of the display. All three modes of operation are controlled by the System Start and System Stop keys. For example, if the system is put in standby mode and the System Start key is not pressed, the RO unit will not operate the flush cycles. This is the same for tank feed and direct feed modes, if the System Start key is not pressed, the RO unit will not operate. The system automatically stops the RO unit whenever a change between tank feed/direct feed and standby modes is made, requiring the operator to restart the RO unit. “SYSTEM STOP” key must be pressed prior to changing between tank feed and direct feed operation. Controls The MC10 is equipped with the following controls and indicators on the front panel of the controller. • 4 x 20 LCD with LED Backlight • Eight LED Indicators for Alarms and Status • 20 Tactile Keys for Control and Data Entry Expansion Port* The MC10 is equipped with one RS-485 expansion port which allows it to be equipped with additional input modules for pressure and flow. The expansion port also allows data from the MC10 to be networked into a larger water treatment monitoring system. The RS-485 expansion port is the 6 pin, watertight connector located in the upper right hand corner of the left hand side of the MC10 enclosure. Use of the expansion port may require a software upgrade to the MC10. Serial Port* The MC10 is equipped with one RS-232 serial port which allows it to be equipped with an optional internal modem module for remote monitoring and downloading of data (program updates, default set points, etc.). The RS-232 serial port is also connected to the 5 pin, watertight connector located directly below the RS-485 expansion port on the left hand side of the MC10 enclosure. Connecting to the serial port on the side of the enclosure will automatically disconnect the internal modem. Data Logging* The MC10 is designed to log data from the RO system. This data may be retrieved locally through the serial port connection or remotely if the MC10 unit is equipped with the optional modem. Remote communication and retrieval of logged data requires the use of AquaGraph PC software. * For use with non-medical VANTAGE RO systems only. (NOT for use with Med-RO systems.) 1-5
Installation 2 Environmental The MC10 is equipped with a NEMA 4X enclosure for use in industrial environments subject to occasional exposure to water sprays and other wet conditions. The MC10 should not be used in explosive environments. General environmental specifications are listed below. Specification Environmental Specifications Rating Storage Temperature -20 to 70 Deg C Ambient Operating Temperature 0 to 55 Deg C Ambient Humidity 30% to 95 % Relative Humidity (Non-Condensing) Mounting The MC10 is designed to be mounted in a horizontal position on a flat surface by means of four mounting holes. Opening the front cover of the enclosure allows access to the mounting holes, access to the bottom holes requires temporary removal of the hinge assemblies. When mounting the MC10, sufficient room should be allowed on the side and bottom of the device for access to the I/O and serial port connections. Mounting dimensions are shown below. Mounting Hole Distance 6.469" Alarm Beeper Overall Depth 5.250" Serial Port Connector Expansion Port Connector Overall Height 7.313" Main Menu Mode=Direct Feed Hrs Since Start=000 System On 1 2 3 4 5 6 7 8 9 CLR 0 ENT Overall Length 10.875" Main Menu LOW QUALITY HIGH TEMP TANK FULL CHEM PUMP FAIL Cord Seals for I/O Connections Mounting Hole Distance 10.000" HIGH PRESSURE LOW PRESSURE PRETREATMENT OUT OVERLOAD SYSTEM START SYSTEM STOP ALARM RESET ALARM SILENCE 7/8" Diameter Hole for Conduit or Cord Grip
Page 1 and 2:
USFilter 10 Technology Drive Lowell
Page 3 and 4:
This manual discloses information i
Page 5 and 6:
TABLE OF CONTENTS SECTION DESCRIPTI
Page 7 and 8:
LC Manual 11/02 Rev. 3 INTRODUCTION
Page 9 and 10:
LC Manual 11/02 Rev. 3 INTRODUCTION
Page 11 and 12:
LC Manual 11/02 Rev. 3 SYSTEM INSTA
Page 13 and 14:
LC Manual 11/02 Rev. 3 SYSTEM INSTA
Page 15 and 16: LC Manual 11/02 Rev. 3 OPERATING IN
Page 21 and 22: SYSTEM MAINTENANCE LC Manual 11/02
Page 31 and 32: TROUBLESHOOTING LC Manual 11/02 Rev
Page 33 and 34: LC Manual 11/02 Rev. 3 WARRANTY 6.1
Page 35 and 36: APPENDIX LC Manual 11/02 Rev. 3 7.1
Page 41 and 42: APPENDIX LC Manual 11/02 Rev. 3 RO
Page 45 and 46: Product Description/Equipment Speci
Page 47 and 48: Process Water Systems General Speci
Page 49 and 50: Process Water Systems Low feed pres
Page 51 and 52: Process Water Systems Skid Cleaning
Page 53 and 54: Series 1, 2 & 3 Pumps Page 1 of 2 [
Page 55 and 56: Product Information FILMTEC Membran
Page 57 and 58: USFilter USFilter USFilter USFilter
Page 59 and 60: Conventions and Symbols ii Special
Page 61 and 62: Table of Contents iv MC10 Overview
Page 63 and 64: Specifications The MC10 incorporate
Page 65: ! The MC10 may be configured to use
Page 69 and 70: I/O The wiring diagram for the inpu
Page 71 and 72: Operation 3 Controls The MC10 is ho
Page 73 and 74: Sequence The normal startup and shu
Page 75 and 76: 7 Perm Divert TD Sec 8 High Temp SP
Page 77 and 78: Time Delays Time delays and deadban
Page 79 and 80: Important Please note: • Temperat
Page 81 and 82: Troubleshooting 5 The MC10 Reverse
Page 83 and 84: Type of Problem Possible Cause or S
show all

Operation and Maintenance Manual for

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?