Operation and Maintenance Manual for

7 Perm Divert TD Sec
8 High Temp SP DegC
9
High Temp DB
DegC
10 High Temp TD Sec
11
12
High Temp Shtdwn
Sec
High Tank Lvl TD
Sec
13 Low Tank Swtch EN
14 Hi Tnk Startup Sec
15
16
17
Low Tank Lvl TD
Sec
High Pressure TD
Sec
Low Pressure TD
Sec
18 Overload TD Sec
19 Pretrt Intlk TD Sec
20* Chem Pump TD Sec
21 Flush Interval Min
22 Flush Duration Sec
23 Feed CND Standard
24 Perm CND Standard
25 Feed Temp Zero
Permeate
Diversion
Time Delay
High
Temperature
Setpoint
High
Temperature
Deadband
High
Temperature
Time Delay
High
Temperature
Shut Down
Delay
High Tank
Level Time
Delay
Low Tank
Switch Enable
High Tank
Level Restart
Time Delay
Low Tank
Level Time
Delay
High Pressure
Time Delay
Low Pressure
Time Delay
Overload
Time Delay
Pretreatment
Interlock Time
Delay
Chemical
Pump Failure
Time Delay
Auto Flush
Interval
Auto Flush
Duration
Feed
Conductivity
Standard
Permeate
Conductivity
Standard
Feed
Temperature
Zero
Calibration
* For use with non-medical VANTAGE RO systems only.
(NOT for use with Med-RO systems.)
1-255 000 15
0-45 00 32
0.1-10 0.0 3
1-255 000 20
1-255 000 10
1-255 000 5
0 or 1 0 1
1-1000 000 30
1-255 000 5
1-255 000 5
0-255 000 5
1-255 000 2
1-255 000 2
0-100 000 2
1-90 000 60
1-360 000 180
10-3000 0000 NA
0-1000 00.0 NA
1-1500 000 NA
Delay (in seconds) before the permeate
diversion valve is activated once the
current value falls below the setpoint.
Temperature setpoint (in deg C) which
activates the high temperature alarm.
Deadband (in deg C) through which the
temperature value must pass before the
high temperature alarm is released.
Delay (in seconds) before the high
temperature alarm is activated once the
current value rises above the setpoint.
Delay (in seconds) before the system
shuts down after the high temperature
alarm is activated.
Delay (in seconds) before the system
shuts down for high tank level.
Allows the system to be configured with
or without a low tank level switch. Enter
“1” to enable (low tank level switch
present) or “0” to disable (low tank level
not being used) this feature.
Delay (in seconds) before the system will
restart after the tank level drops below
the high tank level switch. This feature is
only used when the system is configured
for operation without a low tank level
switch.
Delay (in seconds) before the system
restarts (in Tank Feed mode) when the
level drops below the low tank level
switch.
Delay (in seconds) before the system
shuts down for high pressure.
Delay (in seconds) before the system
shuts down for low pressure.
Delay (in seconds) before the system
shuts down for output overload.
Delay (in seconds) before the system
shuts down for pretreatment interlock.
Delay (in seconds) before the system
shuts down for failure of the chemical
injection pump.
3-5
Interval (in minutes) between autoflush
cycles.
Duration (in seconds) of each autoflush
cycles.
With these settings, the user can
calibrate the conductivity inputs to a
standard solution. See Calibration
section for more information.
This setting allows the temperature
sensor in the feed conductivity cell to be
calibrated to zero degrees C. Only
qualified users following the procedures
documented in the Calibration section of
this manual should adjust this setting.