Operation and Maintenance Manual for

More documents

Recommendations

Info

Process Water Systems Instrumentation Specifications Pressure: Membrane feed 2” dial, liquid filled, brass Filter inlet 2” dial, liquid filled, brass Filter discharge 2” dial, liquid filled, brass Reject 2” dial, liquid filled, brass Low Feed Pressure United Electric, 4-50psi, Brass, ¼” MNPT, 24VDC Switch High Pump Discharge Switch United Electric, 30-600psi, Brass, ¼” MNPT, 24VDC Conductivity: Feed Sensor RODI, 1.0 constant, ¾” MNPT, Epoxy, temperature compensated Product Sensor RODI, 1.0 constant, ¾” MNPT, Epoxy, temperature compensated Monitor RODI, built into microprocessor/controller Flow: Product Flow Indicator Blue White 400N series, PVC/acrylic construction,1/2” FPT connections Reject Flow Indicator Blue White 400N series, PVC/acrylic construction,1/2” FPT connections Recycle Flow Indicator Blue White 400N series, PVC/acrylic construction,1/2” FPT connections Controls Specifications Motor starter NEMA 4X Controller RODI Systems; Microprocessor-Controlled, UL/CUL Listed input/output Discrete 12 point (8 input and 4 output) Warning alarms Low product quality High Pressure Pump Discharge Low feed pressure High feed/product water temperature Shutdown alarms Low product quality High Pressure Pump Discharge Low feed pressure High feed/product water temperature Pretreatment out of service Chemical Feed out of service Motor Overload Storage Tank Full (non-alarming start and stop condition) Status indicator lights Low product quality High Pressure Pump Discharge SV301-LC_rev2.doc Page 4 Rev. 2, 10 Oct 2001
Process Water Systems Low feed pressure High feed/product water temperature Pretreatment out of service Chemical Feed out of service Motor Overload Storage Tank Full Miscellaneous controls Elapsed run time indicator Audible Alarm Serial data port Optional modem Auxiliary contacts – two sets (1 amp maximum) Interface Communication Specifications Pretreatment system - out of service 24VAC discrete input - Note: Activation of this signal confirms that the pretreatment equipment is available to deliver water to the RO unit. (Dry contacts) Call-for-water signal 24VAC discrete input - Note: Activation of this signal confirms that the Chemical Feed equipment is available to deliver water to the RO unit. (Dry contacts) Operating Parameters* Temperature: Maximum Feed Temperature 113°F Minimum Feed Temperature* 50°F *Lower temperature may require larger booster pump Pressure: Maximum System Inlet Pressure 50 PSIG Minimum System Inlet Pressure 15 PSIG Design Membrane Feed Pressure (@77°F) 150 PSIG (Nominal) *If any of the operating conditions are not within the limits given, consult the factory for application assistance. Feed Water Requirements* Parameter: Maximum SDI Rating 3 Maximum Turbidity 1 NTU Maximum Free Chlorine and/or chloramine
Page 1 and 2: USFilter 10 Technology Drive Lowell
Page 3 and 4: This manual discloses information i
Page 5 and 6: TABLE OF CONTENTS SECTION DESCRIPTI
Page 7 and 8: LC Manual 11/02 Rev. 3 INTRODUCTION
Page 9 and 10: LC Manual 11/02 Rev. 3 INTRODUCTION
Page 11 and 12: LC Manual 11/02 Rev. 3 SYSTEM INSTA
Page 13 and 14: LC Manual 11/02 Rev. 3 SYSTEM INSTA
Page 15 and 16: LC Manual 11/02 Rev. 3 OPERATING IN
Page 21 and 22: SYSTEM MAINTENANCE LC Manual 11/02
Page 31 and 32: TROUBLESHOOTING LC Manual 11/02 Rev
Page 33 and 34: LC Manual 11/02 Rev. 3 WARRANTY 6.1
Page 35 and 36: APPENDIX LC Manual 11/02 Rev. 3 7.1
Page 41 and 42: APPENDIX LC Manual 11/02 Rev. 3 RO
Page 45 and 46: Product Description/Equipment Speci
Page 47: Process Water Systems General Speci
Page 51 and 52: Process Water Systems Skid Cleaning
Page 53 and 54: Series 1, 2 & 3 Pumps Page 1 of 2 [
Page 55 and 56: Product Information FILMTEC Membran
Page 57 and 58: USFilter USFilter USFilter USFilter
Page 59 and 60: Conventions and Symbols ii Special
Page 61 and 62: Table of Contents iv MC10 Overview
Page 63 and 64: Specifications The MC10 incorporate
Page 65 and 66: ! The MC10 may be configured to use
Page 67 and 68: Installation 2 Environmental The MC
Page 69 and 70: I/O The wiring diagram for the inpu
Page 71 and 72: Operation 3 Controls The MC10 is ho
Page 73 and 74: Sequence The normal startup and shu
Page 75 and 76: 7 Perm Divert TD Sec 8 High Temp SP
Page 77 and 78: Time Delays Time delays and deadban
Page 79 and 80: Important Please note: • Temperat
Page 81 and 82: Troubleshooting 5 The MC10 Reverse
Page 83 and 84: Type of Problem Possible Cause or S

Operation and Maintenance Manual for

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?