Service Manual - AMS Neve

SynchroNet ES/2 Service Manual
Index
2600 protocol. ......................1:8
access to parameters ................3:2
address decoding ...................1:8
battery backed RAM .................1:7
battery voltage low ..................1:5
bi-phase signals ...................1:14
cable ............................1:16
chase parameters ..................3:14
circuit description. ..............1:1-1:28
clock generator .....................1:5
command and tally interface ..........1:12
command outputs test ................2:3
command parameters ...............3:18
command routine pointers. ...........3:20
comms CTC test ...................2:15
COMMS decoding ...................1:8
COMMS processor ..................1:8
COMMS processor tests .............2:14
comms RAM test ...................2:15
comms SIO test. ...................2:16
CRC test ..........................2:2
CTC test ..........................2:4
DC out b test ......................2:8
DC out test ........................2:6
DC Servo. ........................1:15
DC servo video machine. .............C:1
DC/FM servo ......................1:15
default parameters ..................3:3
diagnostic port .....................1:10
difflock ...........................1:26
display interface ...................1:18
EEPROM..........................1:7
EEPROM test .....................2:20
ES/2 circuit ........................1:2
ESbus interface ....................1:25
event timing ........................1:8
FIFO buffers ......................1:10
fifo test. ..........................2:16
film machine .................1:14 - 1:15
film output test. .................2:4-2:5
FIRQ generator ....................1:11
firq off test ........................2:20
FM out test ........................2:5
FM Servo. ........................1:15
FPGAs............................1:2
frame input test ....................2:19
interface cable .....................1:16
Kernel / Comms interface ............1:10
KERNEL decoding ..................1:9
KERNEL processor ..................1:7
key test ...........................2:3
LED test. ..........................2:3
locate parameters ..................3:14
LTC reader .......................1:23
machine cable selector test. ...........2:9
machine data parameters ............3:27
machine interface ..................1:12
Machine Parameter Menu .............3:2
machine parameters ............3:1-3:28
machine selector resistors. ...........1:16
microprocessor and support ...........1:3
mixed code operation ...............1:26
Motorola M6809E processor ...........1:3
mute/tl test. .......................2:17
paged ROM ........................1:7
parallel command routines ............A:1
parameter protection .................3:2
phase locked loop ..................1:26
power fail signal. ....................1:4
power monitoring. ...................1:4
RAM messages test ................2:16
RAM supply switching ................1:4
reference signals ...................1:20
reference sources ..................1:20
relays. ...........................1:12
reset .............................1:4
resetting default parameters ...........3:3
sdjusting OFFSET on a DC servo video
machine ..........................C:1
serial command routines. .............B:1
serial communications control .........3:25
serial machine control ...............1:17
servo .......................1:14 - 1:15
servo a test ........................2:7
servo controlled wind parameters ......3:23
servo parameters. ...................3:4
setup test. ........................2:11
shuttling ..........................1:14
Sony P2 protocol ....................1:8
Sony serial interface ................1:17
Sony serial test ....................2:12
system block diagram ................1:2
system clock signals .................1:5
tach direction test ...................2:9
tach divider test ....................2:10
tach interface. .....................1:13
tach parameters ....................3:9
tach speed test ....................2:10
tally input test ......................2:3
Issue 1 1:1