Service Manual - AMS Neve

More documents

Recommendations

Info

SynchroNet ES/2 Service Manual Index 2600 protocol. ......................1:8 access to parameters ................3:2 address decoding ...................1:8 battery backed RAM .................1:7 battery voltage low ..................1:5 bi-phase signals ...................1:14 cable ............................1:16 chase parameters ..................3:14 circuit description. ..............1:1-1:28 clock generator .....................1:5 command and tally interface ..........1:12 command outputs test ................2:3 command parameters ...............3:18 command routine pointers. ...........3:20 comms CTC test ...................2:15 COMMS decoding ...................1:8 COMMS processor ..................1:8 COMMS processor tests .............2:14 comms RAM test ...................2:15 comms SIO test. ...................2:16 CRC test ..........................2:2 CTC test ..........................2:4 DC out b test ......................2:8 DC out test ........................2:6 DC Servo. ........................1:15 DC servo video machine. .............C:1 DC/FM servo ......................1:15 default parameters ..................3:3 diagnostic port .....................1:10 difflock ...........................1:26 display interface ...................1:18 EEPROM..........................1:7 EEPROM test .....................2:20 ES/2 circuit ........................1:2 ESbus interface ....................1:25 event timing ........................1:8 FIFO buffers ......................1:10 fifo test. ..........................2:16 film machine .................1:14 - 1:15 film output test. .................2:4-2:5 FIRQ generator ....................1:11 firq off test ........................2:20 FM out test ........................2:5 FM Servo. ........................1:15 FPGAs............................1:2 frame input test ....................2:19 interface cable .....................1:16 Kernel / Comms interface ............1:10 KERNEL decoding ..................1:9 KERNEL processor ..................1:7 key test ...........................2:3 LED test. ..........................2:3 locate parameters ..................3:14 LTC reader .......................1:23 machine cable selector test. ...........2:9 machine data parameters ............3:27 machine interface ..................1:12 Machine Parameter Menu .............3:2 machine parameters ............3:1-3:28 machine selector resistors. ...........1:16 microprocessor and support ...........1:3 mixed code operation ...............1:26 Motorola M6809E processor ...........1:3 mute/tl test. .......................2:17 paged ROM ........................1:7 parallel command routines ............A:1 parameter protection .................3:2 phase locked loop ..................1:26 power fail signal. ....................1:4 power monitoring. ...................1:4 RAM messages test ................2:16 RAM supply switching ................1:4 reference signals ...................1:20 reference sources ..................1:20 relays. ...........................1:12 reset .............................1:4 resetting default parameters ...........3:3 sdjusting OFFSET on a DC servo video machine ..........................C:1 serial command routines. .............B:1 serial communications control .........3:25 serial machine control ...............1:17 servo .......................1:14 - 1:15 servo a test ........................2:7 servo controlled wind parameters ......3:23 servo parameters. ...................3:4 setup test. ........................2:11 shuttling ..........................1:14 Sony P2 protocol ....................1:8 Sony serial interface ................1:17 Sony serial test ....................2:12 system block diagram ................1:2 system clock signals .................1:5 tach direction test ...................2:9 tach divider test ....................2:10 tach interface. .....................1:13 tach parameters ....................3:9 tach speed test ....................2:10 tally input test ......................2:3 Issue 1 1:1
Index SynchroNet ES/2 Service Manual tally interface ......................1:12 tally parameters. ...................3:16 test parameters ....................3:12 test software ..................2:1-2:20 timecode generator .................1:23 timecode interface ..................1:23 timeline test .......................2:12 transport commands ................1:12 unifilm parameters. .................3:22 user interface. .....................1:18 welcome message. ..................2:2 Zeta 3 protocol .....................1:8 1:2 Issue 1
Page 1 and 2:
SynchroNet ES/2 Service Manual 527-
Page 3 and 4:
Contents SynchroNet ES/2 Service Ma
Page 5 and 6:
CIRCUIT DESCRIPTION SynchroNet ES/2
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
ES/2 TEST SOFTWARE SynchroNet ES/2
Page 35 and 36:
ES/2 TEST SOFTWARE SynchroNet ES/2
Page 37 and 38: ES/2 TEST SOFTWARE SynchroNet ES/2
Page 53 and 54: MACHINE PARAMETERS SynchroNet ES/2
Page 81 and 82: APPENDIX A SynchroNet ES/2 Service
Page 83 and 84: APPENDIX A SynchroNet ES/2 Service
Page 85 and 86: APPENDIX B SynchroNet ES/2 Service
Page 87: APPENDIX C SynchroNet ES/2 Service
show all

Service Manual - AMS Neve

Create successful ePaper yourself

Delete template?

Save as template?