Computrac MAX-1000 User's Manual - Arizona Instrument

More documents

Recommendations

Info

8.1.4 The word START in the title means that “START” can be pressed while in thismenu, and the test will begin using the parameters as they have been altered by theuser. This parameter set is automatically saved under the title CUSTOM in theMemory Start list. (See the section entitled MEMORY START MENU on page25.)46
9 MISCELLANEOUS MENU MESSAGES9.1 CONTROL PROGRAM VERSION NUMBERFor troubleshooting purposes, AZI Customer Service may need to know theversion (or revision) of the control program running in your instrument. Todisplay this information, turn the power off, wait a second, and turn it on again.Observe the front panel. The program version number will be displayed in thelower center portion of the screen while the AZI logo is displayed.9.2 DIAGNOSTIC FAILURE MESSAGESThe <strong>MAX</strong>-<strong>1000</strong> contains extensive diagnostic software, which monitors theperformance of the instrument. If a dangerous or abnormal condition is detected,the instrument turns off power to the heater, ends operations, locks the keyboardand displays the following message:SYSTEM ERROR(A brief description of the problem)Software HaltedPower off - < on to reset.If cycling the power switch does not clear the error, stop using the instrument andcall AZI Customer Service (800) 235-3360 or (602) 470-1414.47
Page 1:
USER MANUALCOMPUTRAC ® MAX ® 1000
Page 5 and 6:
PACKING and SHIPPING INSTRUCTIONSTh
Page 7 and 8: Figure 1 MAX-1000 PACKING DIAGRAMvi
Page 9 and 10: TABLE of CONTENTSPACKING and SHIPPI
Page 11 and 12: 12 PERFORMANCE VERIFICATION .......
Page 13 and 14: 1 INTRODUCTIONThe Arizona Instrumen
Page 15 and 16: Location SelectionSelect a location
Page 17 and 18: 2.3.2 Obtain a sample of test mater
Page 19 and 20: 3.4 CONTROLS3.4.1 The front panel c
Page 21 and 22: 3.6.4 After “START” has been pr
Page 23 and 24: 4.1 INSTALLATION OF BALANCE PAN SUP
Page 25 and 26: 4.2 AC POWER CONNECTIONFigure 7 MAX
Page 27 and 28: 4.5 NITROGEN PURGE SETUP4.5.1 Some
Page 29 and 30: 4.7.4 Connect tubing from the conne
Page 31 and 32: 4.10 ENABLE PRINTER OUTPUT4.10.1 Wi
Page 33 and 34: 5 MENU SYSTEM: INSTRUMENT CONFIGURA
Page 35 and 36: 6 “MEMRY” KEY: MEMORY START SEL
Page 37 and 38: 7.1.1 To select a menu item, move t
Page 39 and 40: Test TemperatureThe current setpoin
Page 41 and 42: Start Temp ControlThe START TEMP CO
Page 43 and 44: Some samples contain more than one
Page 45 and 46: The PAN TARE OPTIONS offers the use
Page 47 and 48: ! RESULT DISPLAY OPTIONSTest result
Page 49 and 50: 7.4 CALIBRATION MENU7.4.1 CALIBRATE
Page 51 and 52: connected (IBM or Epson). Select th
Page 53 and 54: tags entered by the operator to ide
Page 55 and 56: ! SYRINGE TESTThis function is usef
Page 57: 8 “PARAM” KEY: TEMPORARILY CHAN
Page 61 and 62: 10.1.4 The final portion of the cur
Page 63 and 64: Figure 54 MOISTURE VS. TEMPERATURE
Page 65 and 66: 11.2.2 The sample should be added e
Page 67 and 68: 12 PERFORMANCE VERIFICATIONPeriodic
Page 69 and 70: eliable results, use a high quality
Page 71 and 72: 13 ROUTINE MAINTENANCEThe MAX-1000
Page 73 and 74: 13.3 SAMPLE PAN SUPPORTThe sample p
Page 75 and 76: SYMPTOM DIAGNOSIS REMEDYNo power to
Page 77 and 78: TEMPERATURE CIRCUITProbable cause:A
Page 79 and 80: FeatureSpecificationTest DisplayInt
Page 81 and 82: 18 APPENDIX A18.1 PARAMETER DEVELOP
Page 83 and 84: PARAMETER DOCUMENTATION:To ensure o
Page 85 and 86: If smaller standard deviations are
Page 87 and 88: 21 MAINTENANCE CONTRACTArizona Inst
show all

Computrac MAX-1000 User's Manual - Arizona Instrument

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?