Connection to the SysKonnect SK-54P1 802.11g Wireless Print Server

More documents

Recommendations

Info

28 3 Windows Configuration The name of the attached printer will be displayed if possible. If "No printer" is displayed, check that the printer is properly connected and powered on. If your SysKonnect SK-54P1 802.11g Wireless Print Server is not listed: 1. Click the REFRESH button. 2. Check that both the SysKonnect Print Server and the printer are properly connected and powered on. 3. Check that the SysKonnect Print Server has been configured. (Use the setup wizard on the CD-ROM.) 4. If using TCP/IP, try installing the NetBEUI protocol. (For details, see section "Checking your Network Protocols (Windows 9x)" on page 22.). Then try again. 5. Select the port to which the SysKonnect SK-54P1 802.11g Wireless Print Server is connected. 6. Click NEXT. If you see the following error message, either install Internet Explorer 4 or later, or follow the procedure in section "Windows Printing Problems" on page 86. Figure 11. Error Message: “Required File not found” A pop-up message will inform you if the port has been created successfully. Then a screen like the following will be displayed. Figure 12. “Configure Printer Port” Screen 7. Select the correct Windows printer in the printers list. 8. Click the CONNECT button. 9. If the correct printer type is not listed, click ADD NEW PRINTER to run the Windows “Add Printer” wizard. Step through the wizard and install the required printer: • Select the correct printer manufacturer and model, or use the HAVE DISK option if appropriate.
Windows Peer-to-Peer Printing 29 i Epson Spooler Manager SysKonnect SK-54P1 802.11g Wireless Print Server We recommend changing the printer name to indicate which device is on (e.g. HP2100 on SCA43600_P1). • If you were asked about sharing the printer, do not enable SHARING. When the printer installation is finished, it will be listed in the “Configure Printer Port” screen above. • Select the printer. • Click CONNECT. The installation is now complete. You can print now by using this printer. To install additional printers, repeat the instructions given in step 9. If using the Epson Spooler Manager, this program must be disabled, as follows: 1. Run the Epson Spooler Manager. 2. Select QUEUE SETUP from the menu. 3. Click USE PRINT MANAGER FOR THIS PORT. 4. Click OK to exit. Management Print jobs can be managed like any Windows printer: 1. Open the printers folder (START > SETTINGS > PRINTERS). 2. Double-click any printer to see the current print jobs. If the printer attached to the SysKonnect SK-54P1 802.11g Wireless Print Server has changed, just run the setup program again, and select the correct printer. To delete a port created by this setup program, use the Windows facility DELETE PORT: 1. Assuming that you have printers installed, right-click any printer in the printers folder. 2. Select PROPERTIES. 3. Click the DELETE PORT button. This button is on the DETAILS or PORTS tab, depending on your Windows version. If the SysKonnect SK-54P1 802.11g Wireless Print Server's IP address has changed, and you cannot print, delete the port (see procedure above) and re-install it. Advanced Port Options Use the Start menu to run this program in future. The default installation is START > PRO- GRAMS > PRINT SERVER DRIVER > PRINT DRIVER SETUP. The options for peer-to-peer printing are accessed via the PORT SETTINGS button: 1. Use START > SETTINGS > PRINTERS to open the printers folder. 2. Right-click the printer. 3. Select PROPERTIES. 4. Click the PORT SETTINGS button. This button is on the DETAILS or PORTS tab, depending on your Windows version. A screen like the following is displayed:
Page 1: SysKonnect SK-54P1 User Manual Wire
Page 4 and 5: 4 Copyright © SysKonnect GmbH, 200
Page 6 and 7: 6 Conventions Examples: The “Crea
Page 8 and 9: 8 Table of Contents AppleTalk Setup
Page 10 and 11: 10 Table of Figures Figure 44: Sele
Page 12 and 13: 12 Safety Precautions
Page 14 and 15: 14 1 Introduction Package Contents
Page 16 and 17: 16 1 Introduction
Page 18 and 19: 18 2 Installation
Page 20 and 21: 20 3 Windows Configuration Figure 2
Page 22 and 23: 22 3 Windows Configuration Printing
Page 24 and 25: 24 3 Windows Configuration Windows
Page 34 and 35: 34 3 Windows Configuration Adding T
Page 36 and 37: 36 3 Windows Configuration
Page 38 and 39: 38 4 Unix System Configuration Othe
Page 40 and 41: 40 4 Unix System Configuration •
Page 42 and 43: 42 4 Unix System Configuration Exam
Page 44 and 45: 44 5 Novell NetWare Configuration T
Page 46 and 47: 46 5 Novell NetWare Configuration
Page 48 and 49: 48 6 Macintosh Configuration Macint
Page 50 and 51: 50 7 BiAdmin Management Utility Dev
Page 52 and 53: 52 7 BiAdmin Management Utility Upg
Page 54 and 55: 54 7 BiAdmin Management Utility Con
Page 56 and 57: 56 7 BiAdmin Management Utility App
Page 58 and 59: 58 7 BiAdmin Management Utility Int
Page 60 and 61: 60 7 BiAdmin Management Utility Wir
Page 62 and 63: 62 7 BiAdmin Management Utility Wir
Page 64 and 65: 64 7 BiAdmin Management Utility
Page 66 and 67: 66 8 Web-Based Management Connectio
Page 68 and 69: 68 8 Web-Based Management IP Addres
Page 70 and 71: 70 8 Web-Based Management Security
Page 72 and 73: 72 8 Web-Based Management Other Scr
Page 74 and 75: 74 9 Special Features Installing us
Page 76 and 77: 76 9 Special Features i IPP Client
Page 78 and 79:
78 9 Special Features Internet Mail
Page 80 and 81:
80 9 Special Features 2. Provide th
Page 82 and 83:
82 9 Special Features i Printing th
Page 84 and 85:
84 10 Troubleshooting Problem Solut
Page 86 and 87:
86 10 Troubleshooting Windows Print
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
92 10 Troubleshooting Unix Troubles
Page 94 and 95:
94 11 Important Information i 4. Se
Page 96 and 97:
96 11 Important Information
Page 98 and 99:
98 Appendix A. License and Warranty
Page 100:
100 Appendix A. License and Warrant
show all

Connection to the SysKonnect SK-54P1 802.11g Wireless Print Server

Create successful ePaper yourself

Delete template?

Save as template?