XProtect Express 1.1; Administrator's Manual - Milestone

More documents

Recommendations

Info

Milestone XProtect ® Express 1.1Administrator's ManualNameEvent nameSend e-mail if this event occursAttach image from cameraDeleteAddDescriptionSpecify a name. Names must be unique, and must not contain any of thesespecial characters: < > & ' " \ / : * ? | [ ]Some cameras only support event names of a certain length and/or with acertain structure. Refer to the camera's documentation for exact details.Only available if e-mail notification (see "Configure e-mail notifications" onpage 132) is enabled. Select if XProtect Express should automatically sendan e-mail when the event occurs. Recipients are defined as part of the e-mail notification configuration. When using e-mail notifications, also bear inmind individual cameras' scheduling (see "E-mail notification" on page127).Only available if e-mail notification (see "Configure e-mail notifications" onpage 132) is enabled. Select to include an image—recorded at the time theevent is triggered—in the e-mail notification, then select the requiredcamera in the list next to the check box.Delete a selected event.Add a new event. When Global or a specific camera is selected, clickingAdd will add a new manual event. When a specific manual event isselected, clicking Add will add a timer event (on page 113) to the selectedmanual event.Timer eventWhen you add timer events (see "Add a timer event" on page 113), specify the following properties:NameTimer event nameTimer event occurs afterDescriptionSpecify a name. Names must be unique, and must not contain any of thesespecial characters: < > & ' " \ / : * ? | [ ]Some cameras only support event names of a certain lengthand/or with a certain structure. Refer to the camera'sdocumentation for exact details.Specify the amount of time that should pass between the main eventoccurring and the timer event (in seconds or minutes).Hardware outputWhen you add hardware output (see "Add a hardware output" on page 112), specify the following properties:www.milestonesys.com 116 Advanced configuration
Milestone XProtect ® Express 1.1Administrator's ManualNameOutput nameOutput connected toKeep output forDescriptionSpecify a name. If you are going to make the hardware output available formanual activation in clients, this is the name that client users will see.Names must be unique, and must not contain any of these specialcharacters: < > & ' " \ / : * ? | [ ]Some cameras only support event names of a certain lengthand/or with a certain structure. Refer to the camera'sdocumentation for exact details.Select which of the hardware device's output ports the output is connectedto. Many hardware devices only have a single output port; in that casesimply select Output 1.Lets you specify the amount of time for which the output should be applied.Specify the required amount of time in either 1/10 seconds or seconds.Some hardware devices are only able to apply output for arelatively short time, for example for up to five seconds. Refer tothe documentation for the hardware device in question for exactinformation.Tip: To verify that your hardware output works, click the Test Output button.Scheduling and archivingAbout schedulingThe scheduling feature lets you specify: When you want to archive (see "About archiving" on page 118)That some cameras transfer video to XProtect Express at all timesThat some cameras transfer video only within specific periods of time or when specific events occurWhen you want to receive notifications from the systemYou can set up general scheduling properties for all your cameras or individual properties per camera. You canset up when:One or more cameras should be online (that is transfer video to XProtect Express)One of more cameras should use speedup (that is use a higher than normal frame rate)You want to receive any e-mail notifications regarding one or more cameras.Archiving takes place.PTZ cameras should patrol, and according to which patrolling profilewww.milestonesys.com 117 Advanced configuration
Page 1 and 2:
Milestone SystemsXProtect ® Expres
Page 3 and 4:
Milestone XProtect ® Express 1.1Ad
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 18 and 19:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66: Milestone XProtect ® Express 1.1Ad
Page 115: Milestone XProtect ® Express 1.1Ad
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183:
About Milestone SystemsFounded in 1
show all

XProtect Express 1.1; Administrator's Manual - Milestone

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?