XProtect Express 1.1; Administrator's Manual - Milestone

More documents

Recommendations

Info

Milestone XProtect ® Express 1.1Administrator's ManualWhen you use this option, you configure client users separately from clients' access. See Add individual users(see "Add basic users" on page 138), Add user groups (on page 139), and Configure user and group rights (onpage 140).Server access propertiesProperties in this window:Server access .................................................................................................... 136Local IP ranges .................................................................................................. 137Language support and XML encoding ............................................................... 137Server accessWhen you configure server access (on page 135) (that is clients' access to the XProtect Express server), specifythe following:NameServer nameLocal portEnable internet accessInternet addressInternet portDescriptionName of the XProtect Express server as it will appear in clients. Clientusers with rights to configure their clients will see the name of the serverwhen they create views in their clients.Port number to use for communication between clients and the surveillanceserver. The default port number is 80; you can change the port number ifport 80 is used for other purposes in your organization.Select the check box if the server should be accessible from the internetthrough a router or firewall. If you select this option, also specify the public(“outside”) IP address and port number in the following fields. When usingpublic access, the router or firewall used must be configured so requestssent to the public IP address and port are forwarded to the local (“inside”)IP address and port of the XProtect Express server.Lets you specify a public IP address or hostname for use when theXProtect Express server should be available from the internet.Specify a port number for use when the XProtect Express should beavailable from the Internet. The default port number is 80. You can changethe port number if needed.www.milestonesys.com 136 Advanced configuration
Milestone XProtect ® Express 1.1Administrator's ManualNameMax. number of clientsDescriptionYou can limit the number of clients allowed to connect at the same time.Depending on your XProtect Express configuration and the performance ofthe hardware and network used, limiting the number of simultaneouslyconnected clients may help reduce server load. If more than the allowednumber of simultaneously connected clients attempt to log in, only theallowed number of clients will be allowed access. Any clients in excess ofthe allowed number will receive an error message when attempting to login.By default, a maximum of ten simultaneously connected clients areallowed. To specify a different maximum number, simply overwrite thevalue.Tip: To allow an unlimited number of simultaneously connected accessclients, type 0 (zero) in the Max. number of clients field.A four-minute session timeout period applies for client sessions onXProtect Express. In many cases, client users may not notice this at all.However, the session timeout period will be very evident if you set the Max.number of clients value to 1. When that is the case, and the singleallowed client user logs out, four minutes must pass before it will bepossible to log in again.Local IP rangesYou can specify IP address ranges which XProtect Express should recognize as coming from a local network.This can be relevant if different subnets are used across you local network.1. Click the Add button.2. In the Start Address column, specify the first IP address in the required range.3. In the End Address column, specify the last IP address in the required range.Tip: If required, an IP address range may include only one IP address (example: 192.168.10.1-192.168.10.1).4. Repeat if other local IP address ranges are required.Language support and XML encodingYou can select the language/character set that should be used by the XProtect Express server and clients.NameCharacter encoding/LanguageDescriptionSelect required language/character set.Example: If the surveillance server runs a Japanese version of Windows,select Japanese. Provided access clients also use a Japanese version ofWindows, this will ensure that the correct language and character encodingis used in clients' communication with the server.www.milestonesys.com 137 Advanced configuration
Page 1 and 2:
Milestone SystemsXProtect ® Expres
Page 3 and 4:
Milestone XProtect ® Express 1.1Ad
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 18 and 19:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86: Milestone XProtect ® Express 1.1Ad
Page 135: Milestone XProtect ® Express 1.1Ad
Page 183: About Milestone SystemsFounded in 1
show all

XProtect Express 1.1; Administrator's Manual - Milestone

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?