Heavy Duty Balanced Opposed Compressors

More documents

Recommendations

Info

FOR MODELS: JG AND JGA SECTION 6 - TECHNICAL ASSISTANCE Problem Possible Causes Piston Rod Oil Wiper Leaks Force Feed Lube No- Flow Shutdown Worn wiper rings. Wipers incorrectly assembled. Worn/scored rod. Improper fit of rings to rod/side clearance. Blockage causing blow-out disk to vent. Force feed filter(s) dirty. Force feed pump failure. Distributor block failure. Loss of force feed oil supply to pump. DNFT failure. Oil injection point check valve failure. PAGE 6 - 6 11/01
FOR MODELS: JG AND JGA SECTION 7 - APPENDICES Ariel Tools Ariel Furnished Tools Ariel provides one tool box with each unit with tools included in the box as listed below (see Figure 7-1:). • Peg Wrench for Round Crosshead Nuts 3/4" Diameter (A-0076) • Open End Wrench for Hex Crosshead Nuts 2" (B-0016) • Ratchet Extension Support (B-1240) • 1/4" x 3/8" UNF Valve Tool for Installing or Removing Valves (A-0409) • 5/16" x 1/2" UNF Valve Tool for Installing or Removing Valves (A-0135) • Piston Nut Spanner for 3/4" Square Drive Ratchet (A-0279) Piston Turning Tool for 9/16” socket (A-1678) provided with small tandem cylinders • only Crank End Clearance Setting Tool 0.035” (0.89 mm) special tool provided for 2-3/4M, • 3M, 2-3/4P-CE and 3-14P-CE class cylinders only (A-8159) Torque Chart (D-2159) • Ariel provides these tools with every compressor. Please contact your Distributor if you do not have these tools. These tools are specifically designed for use on Ariel units. Clean all tools before use. Ensure that the tool and the part being removed or installed are fully engaged during the process. If a tool is missing, worn or broken, please call your distributor for a replacement. Do not use substitute, worn or broken tools. Also included in the tool box are standard commercial tools as follows: • Allen Wrenches: 3/32”, 1/8", 9/64”, 5/32", 3/16", 1/4”, 5/16” & 3/8" Ariel Optional Tools • Piston and Rod Clamping Fixture (D-0961) (see Figure 5-11: on page 5-19) • Force Feed Lubricator Bearing Housing Spanner Wrench (A-8158) • Force Feed Lubrication Hand Purge Pump (G-7162) • Piston Rod Entering Sleeve (A-8561) 11/01 PAGE 7 - 1
Page 1 and 2:
ARIEL Heavy Duty Balanced Opposed C
Page 3 and 4:
FOR MODELS: JG AND JGA TABLE OF CON
Page 5 and 6:
FOR MODELS: JG AND JGA TABLE OF CON
Page 7 and 8:
FOR MODELS: JG AND JGA SECTION 1 -
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72: FOR MODELS: JG AND JGA SECTION 4 -
Page 121: FOR MODELS: JG AND JGA SECTION 6 -
show all

Heavy Duty Balanced Opposed Compressors

Create successful ePaper yourself

Delete template?

Save as template?