Heavy Duty Balanced Opposed Compressors

More documents

Recommendations

Info

FOR MODELS: JG AND JGA SECTION 4 - LUBRICATION AND VENTING Force Feed Pumps The force feed pumps are attached to and driven by the lube box. Pump features include a one piece steel pump body, modular cast iron cylinder (barrel and plunger) assembly, hardened steel roller rocker arm, weatherproof construction and is suitable with mineral or synthetic lubricants. If the barrel and plunger fail on a force feed pump, replace the entire pump assembly. Do not repair a pump, except for replacement of external parts, such as spring, spring retainer, snap ring, outlet check valve and seal washer, rubber boot and or pump assembly to lube box. Locknut Rubber Boot Snap Ring Flushing Unit Outlet Check Valve and Seal Washer Gasket FIGURE 4-1: FORCE FEED PUMP Spring and Spring Retainer Force Feed Lubricator Adjustment See instructions “Force Feed Lubricator Adjustment” on page 3-8 and see Figure 5-10:. NOTE: THE FORCE FEED SYSTEM MUST HAVE A BLOW-OUT DISC BETWEEN THE FORCE FEED LUBRICATOR PUMP AND THE NO-FLOW SHUTDOWN. THE FORCE FEED SYSTEM MUST HAVE A WORKING NO-FLOW SHUTDOWN SET TO ACTUATE WITHIN THREE TO FIVE MINUTES AFTER INTERRUPTION OF THE LUBRICATOR OIL FLOW. PAGE 4 - 12 11/01
FOR MODELS: JG AND JGA SECTION 4 - LUBRICATION AND VENTING Blow-Out Fittings and Rupture Disks TABLE 4-2: BLOW-OUT FITTING ASSEMBLIES AND REPLACEMENT RUPTURE DISKS SUPPLIER BLOW-OUT FITTING ASSEMBLY ARIEL P/N RATED PSI RATED MPa REPLACEMENT RUPTURE DISK a ARIEL P/N COLOR THICKNESS INCHES mm Lincoln A-0080 3250 22.4 A-0124 Purple 0.0225 0.57 Lubriquip A-3531 3700 26 A-3536 Yellow 0.010 0.28 Lubriquip A-3532 4600 32 A-3537 Red 0.012 0.30 Lubriquip A-3533 5500 38 A-3538 Orange 0.014 0.36 Lubriquip A-3534 6400 44 A-3539 Aluminum 0.016 0.41 Lubriquip A-3535 7300 50 A-3540 Blue 0.020 0.51 a. Do not use a Lincoln replacement rupture disk in a Lubriquip blow-out fitting assembly, nor a Lubriquip disk in a Lincoln fitting. See Figure 1-15 on page 1-15 for blow-out fitting cap tightening torque. Do not over tighten cap or blow-out pressure can be reduced. Fitting FIGURE 4-2: LINCOLN ST. LOUIS BLOW-OUT FITTING ASSEMBLY (P/N A-0080 ONLY) Fitting Rupture Disk Rupture Disk Cap Cap 1/4 Inch (6mm) Diameter Hole 1/8 Inch (3mm) Diameter Hole FIGURE 4-3: LUBRIQUIP BLOW-OUT FITTING ASSEMBLY 11/01 PAGE 4 - 13
Page 1 and 2:
ARIEL Heavy Duty Balanced Opposed C
Page 3 and 4:
FOR MODELS: JG AND JGA TABLE OF CON
Page 5 and 6:
FOR MODELS: JG AND JGA TABLE OF CON
Page 7 and 8: FOR MODELS: JG AND JGA SECTION 1 -
Page 57: FOR MODELS: JG AND JGA SECTION 4 -
Page 109 and 110:
FOR MODELS: JG AND JGA SECTION 5 -
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
show all

Heavy Duty Balanced Opposed Compressors

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?