12LS Controller Installation and Operation Manual, Rev 3 ... - Watlow

More documents

Recommendations

Info

. Input TypesThe following one byte codes designate the various input types accepted by the 12LS:Code Input Type------------ ---------------00 Linear (0-60 mV)01 J Thermocouple02 K Thermocouple03 T Thermocouple04 [ Spare ]05 [ Spare ]06 RTD07 Frequency (Pulse Counter). Output TypesOutput type codes are one byte hexadecimal designations formed by setting the individual bits, asexplained below, to their proper state.___7______6______5______4______3______2______1______0____|Cntrl | On | | | |Auto |Digital| DZC ||Action| / | | | | / | / | / || | Off| | | |Manual|Analog| TP ||______|______|______|______|______|______|______|______|| | | | | || | | | || | | | 0 = Distributed| | | | Zero Crossing| | | | (DZC)| | | | || | | | 1 = Cycle Time| | | | Proportioned| | | || | | 0 = Digital Output| | | 1 = Analog Output| | || | 0 = PID Control ON| | 1 = PID Control OFF| || 0 = ON/OFF Control Disabled| 1 = ON/OFF Control Enabled|0 = Reverse Acting Output1 = Direct Acting Output8-3
The following examples show the output code for specific output types:Output ConfigurationHex Code--------------------------------------- --------DZC Digital Output, Automatic control 00Time Proportioned Digital Output, Automatic control 01Analog output, Automatic control 02DZC Digital Output, Manual Control 04Time Proportioned Digital Output, Manual control 05Analog output, Manual control 06ON/OFF Digital Output, Automatic control 40ON/OFF Digital Output, Manual control 44DZC Output, Automatic Control, Inverted Output 80Time Proportioned Output, Automatic Control, Inverted Output 81Analog Output, Automatic Control, Inverted Output 82DZC Output, Manual Control, Inverted Output 84Time Proportioned Output, Manual Control, Inverted Output 85Analog Output, Manual Control, Inverted Output 86ON/OFF Output, Automatic Control, Inverted OutputC0ON/OFF Output, Manual Control, Inverted OutputC48-4
Page 1 and 2:
ANAFAZE 12LSInstallation And Operat
Page 3 and 4:
WARNINGANAFAZE HAS MADE EFFORTS TO
Page 5 and 6:
4.4 OPERATIONAL MENUS..............
Page 7 and 8:
vii
Page 9 and 10:
The ANAFAZE 12LS front panel provid
Page 11 and 12:
Digital Inputs and Outputs Expand V
Page 13 and 14:
2.2 Control CapabilityNumber of Loo
Page 15 and 16:
3.0 INSTALLATIONThere are some prec
Page 17 and 18:
1/8th DIN HOUSING3-3
Page 19 and 20:
4. Use Thermocouple Extension Wire
Page 21 and 22:
3. Separate the 120 vac power leads
Page 23 and 24:
REMOTE TERMINAL BLOCK CONNECTIONSTh
Page 25 and 26:
3.3.5 INPUT SCALINGThe ANAFAZE 12LS
Page 27 and 28:
WARNINGUse of the grounded T/C, mea
Page 29 and 30:
3.4.1 PID CONTROL AND ALARM OUTPUTS
Page 31 and 32:
3.5.3 RS-485 DESCRIPTIONThe EIA Sta
Page 33 and 34:
ANAFAZE 12LS connections for a sing
Page 35 and 36:
|- - - - - - - - - - - - - -|Back|-
Page 37 and 38:
4.2 DISPLAYSOn power-up the control
Page 39 and 40:
|----------------------------------
Page 41 and 42:
4.3 GENERAL PROGRAMMING AND EDITING
Page 43 and 44:
4.4.2 SET LOOP TO MANUAL/AUTOTo tog
Page 45 and 46:
LOOP SETUP DATA|-------------------
Page 47 and 48:
The menu appears as:|--------------
Page 49 and 50:
4.5.1.6 POWER UP OUTPUT STATUSThis
Page 51 and 52:
Press YES to select the menu or NO
Page 53 and 54: The display appears as :|----------
Page 55 and 56: The low input reading is referenced
Page 57 and 58: 4.5.3.1 PROPORTIONAL BANDThe first
Page 59 and 60: |----------------------------------
Page 61 and 62: Press UP and DOWN to set the maximu
Page 63 and 64: 4.5.5.4 DEVIATION BAND ALARMThis me
Page 65 and 66: Press ENTER to store the status or
Page 67 and 68: 4.6 RAMP AND SOAK OPTIONThe ramp an
Page 69 and 70: +----------------------------------
Page 71 and 72: 4.6.3 PROFILE STATUS DISPLAYWhether
Page 73 and 74: An example display follows:|-------
Page 75 and 76: |----------------------------------
Page 77 and 78: PROFILE SETUP GUIDE4-44
Page 79 and 80: UP/DOWNSelect a profile designator
Page 81 and 82: When any segment is out of toleranc
Page 83 and 84: 4.7.6 EDIT EXTERNAL RESETFrom this
Page 85 and 86: YESChange current setpoint setting.
Page 87 and 88: 4.7.13 EDIT SEGMENT TRIGGERSUse thi
Page 89 and 90: 4.7.16 EDIT TRIGGER LATCH STATUSDis
Page 91 and 92: 4.7.19 EDIT PROFILE CYCLESThis menu
Page 93 and 94: 5.1.5 DISTRIBUTED ZERO CROSSINGDist
Page 95 and 96: There is no tuning step for the Out
Page 97 and 98: 5.2.6 GENERAL PID CONSTANTS BY APPL
Page 99 and 100: 7.0 TROUBLE SHOOTING INFORMATION7.1
Page 101 and 102: If ANASOFT runs then the next step
Page 103: Data Boundary ErrorThis Error Code
Page 107 and 108: Cycle TimeDeviationAlarmThe time ba
Page 110: Congratulations! You have obtained
show all

12LS Controller Installation and Operation Manual, Rev 3 ... - Watlow

Create successful ePaper yourself

Delete template?

Save as template?